Stations in washing system, Mechanical Engineering

Assignment Help:

Washing:

Station 1

Loading bay START

Station 2

Hot Chemical wash

Station 3

Running Cold bath

Station 4

Hot Chemical wash

Station 5

Running Cold bath

Station 6

Hot water rinse

Station 7

Loading bay      END

Table: Show the stations in washing system

This is the final process of blade production before goes to assembly and packing. Washing process in here is essential toward the quality of the blade material. Our wash stations consist of 7 sections. Operator will be ready at station 1 to do blade loading and tighten up the hanger. After everything is tied up and data been taken for quality control purpose, operator will proceed to dip blades into station 2. We are using stainless steel care chemical mixture with water. We will boil up station 2 to the temperature approximate 80 ºC to 85 ºC. Washing takt time for station 2 is around 90 second. After washing, blades will transfer and rinse with running cold water. Rinsing takt time for station 3 is around 20 second. Steps will repeat the same as station 2 for station 4. Whereby only different is takt time for station 4 is 70 second.  After rinsing at station 5, the washing at last station 6 will increase to 90 ºC with just only hot water. At last station 7 will be loading bay and pneumatic air gun will blow off the water.


Related Discussions:- Stations in washing system

Calculate value of cutting speed, a) A carbide tool with mild steel work pi...

a) A carbide tool with mild steel work piece was found to give life of 2hours while cutting at 50 mpm. Calculate the tool life if the same tool is used at a speed 25% higher than p

Engineering physics-1, how will you detect the depth of sea and application...

how will you detect the depth of sea and application?

Motorcycle servicing , In motorcycle servicing we studied about various ser...

In motorcycle servicing we studied about various service tips for motorcycle servicing. These steps will ensure proper servicing of motorcycle and as a result customers will trust

Draw a diagram of a simple carburettor, a) Draw a diagram of a simple carbu...

a) Draw a diagram of a simple carburettor and briefly explain its function. b) What are the basic characteristics of fuels for CI engines.

Fuel consumption is high motorcycle problem, If Fuel Consumption is High ...

If Fuel Consumption is High Causes of Problem Remedy   Incorrect electrode gap of spark plug Worn out electrodes o

Formed heads of vessels, Q. Formed heads of vessels? Formed heads are g...

Q. Formed heads of vessels? Formed heads are generally of 2:1 semi ellipsoidal form, but other heads may be used, such as hemispherical, torispherical, conical and toriconical.

Design the drainage area, Q. Design the drainage area? Areas beneath eq...

Q. Design the drainage area? Areas beneath equipment or vessels subject to spills or leaks shall have slope drainage area. Every skid shall be provided with floor drains. S

Steps of centrifugal filter and screen filter cleaning, Centrifugal Filter ...

Centrifugal Filter and Screen Filter Cleaning :   Oil may contain impurities. Since the oil passes through all the engine parts, the impurities may harm the parts and cause imprope

Evaluate the point of contraflexure, Evaluate the point of contraflexure: ...

Evaluate the point of contraflexure: An overhanging beam of 15 m span is carrying a consistently distributed load of 1 kN/m over the length of 10 m at a distance 5 m from the

Determine the economic order quantity, Determine the economic order quantit...

Determine the economic order quantity: Determine the economic order quantity and the reorder point. Given Annual demand (D) = 2,000 units Average daily demand (d) = 2,00

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd