Show material selection process, Mechanical Engineering

Assignment Help:

Q. Show Material selection process?

• Design life shall be based on project design criteria and normally 10 to 15 years' service life specified for well pads, 20-25 years for CPF and 30 years for Pipeline. In some low pressure system or exchanger tube bundles, early replacement may permit using less expensive materials with less than normal design life.

• Material selection shall be based on operating conditions. Short term operating conditions like, start-up, shutdown and steam outs or upset conditions like loss of flow or pressure upset shall also be considered in material selection.

• Material requirements for sour services shall be in full compliance with the latest edition of NACE MR0175/ISO15156 unless requested otherwise by Customer. Sour service determination is based upon operating condition for plant facilities and design condition for pipeline.

• PWHT requirements shall be considered mandatory in sour services for pressure equipment. Process piping may be excluded provided all the fabrication requirements of NACE MR0175/ISO15156 are met.

• Low ambient temperature code requirements are not normally specified and shall be addressed in line designation tables and equipment data sheets for piping and equipment, respectively. Only low temperature due to process reasons shall be addressed.


Related Discussions:- Show material selection process

Spot welding of different metals-nickel and monel metal, Spot welding of di...

Spot welding of different metals-Nickel and monel metal While spot welding these materials, the settings are to be properly maintained. Welding time, in this case, is only 50 %

Resistance welding, RESISTANCE WELDING The types are as follows: ...

RESISTANCE WELDING The types are as follows: Resistance Spot Welding Resistance Seam Welding Projection Welding Flash Butt Welding Flash Butt Welding Stit

Show the geometric similarity, Q. Show the Geometric Similarity? When m...

Q. Show the Geometric Similarity? When model is required to provide an aid merely for visualisation, scaler reproduction of form is sufficient which is termed Geometric Similar

What is the pressure difference between the stations , (Bernoulli equation ...

(Bernoulli equation along a streamline) Water flows from station (1) to (2) around an expanding corner pipe, 3m high. The speed along the center streamline is 10 m/s at (1) and 5

Find out the centroid of an area of a semicircle, Find out the centroid of ...

Find out the centroid of an area of a semicircle: Find out the centroid of an area of a semicircle illustrated in Figure. Solution You shall note that it is not p

Explain the construction and working of a differential, (a) What are the di...

(a) What are the different types of clutches used in modern automobiles? With the help of neat and clean diagram describe the functioning of a diaphragmspring clutch. (b) Explai

Corrosive properties of caustic, Q. Corrosive properties of caustic? So...

Q. Corrosive properties of caustic? Sodium hydroxide, more commonly known as Caustic Soda or simply ‘Caustic', is widely used in the petrochemical industry to neutralize acidic

Third gear position - shifting of gear, Third Gear Position: When gea...

Third Gear Position: When gear M3 on the main shaft is in mesh with gear C3 on the counter shaft then this is known as third gear position. The fixed gear M3 rotates with mai

Principle of equilibrium - mechanics, Principle of equilibrium: Sol.:...

Principle of equilibrium: Sol.: Principle of equilibrium can be divided in to three main parts; (1) Two Force Principle: As the Resultant is zero when body is in equili

Advantages of laser welding process, Advantages of Laser Welding Process ...

Advantages of Laser Welding Process   1) Narrow deep penetration welds capable of being produced in atmosphere. 2) Low thermal distortion - due to less heat input and paral

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd