Mine Surveying.., Other Engineering

Assignment Help:
Question 1 (100 marks)
As Surveyor in charge of an underground mine you have been instructed to design a tunnel to join a crosscut to a haulage drive. The details of the crosscut and drive are shown below.
Crosscut - Bearing: 71°06''25”
Grade: 1:70
Last Survey Station: 5417.744 E
2448.954 N
1099.439 RL Floor


Haulage drive - Bearing: 312°33''10”
Grade: -1:100
Last Survey Station: 5594.088 E
2384.402 N
1152.447 RL Floor

The face of the crosscut is 80m ahead of the last station. Both the crosscut and haulage drive
are 5m wide and 4m high.
The tunnel is to have a circular horizontal alignment turning right from the crosscut with aradius of not more than 50m and not less that 30m with a maximum grade of 1 in 10.

a. Calculate the co-ordinates of the two tangent points for the most cost effective solution.
(40)

b. Plot the crosscut and drives at suitable scale showing all relevant information. Show the proposed walls as dashed lines on the plan. (10)

c. Calculate the co-ordinates of a point (Stn 425) that is 5m along the centreline of the tunnel from the TP in the crosscut (TP1). Check your calculations using the plan. (5)

d. From this point a chord line bearing 88°43’ is to be set out. At 2m intervals calculate the centreline offsets from this line and reduced levels of the floor. (40)

e. At what chainage from Stn 425 should mining cease and why? (5)



I''m wondering I got an assignment that due date tomorrow and it contains 5 questions and i solve all of them except the first one, so if able to solve it just let me know

Related Discussions:- Mine Surveying..

Building economics, with sketches,describe single upper flows

with sketches,describe single upper flows

Time-flow diagram, One approach of an intersection with fixed time traffic ...

One approach of an intersection with fixed time traffic signals, vehicles arrive at 500 veh/h on the approach. The cycle time of the intersection is 80 seconds, and the effective g

Production Inventory Control, Modular Forniture Company manufactures two ki...

Modular Forniture Company manufactures two kinds of couches: Suede and Leather. The forecasted demand for

Aero Performance Problem, Given data for an F-4 (W=40000 lb, S=530 ft^2, Ta...

Given data for an F-4 (W=40000 lb, S=530 ft^2, Ta@sea level=35800 lb, Mach=1.5, h=20000 ft (std day), Cd0=.0224, k=.1516) find aircraft''s specific excess power in straight-and-lev

Fire prevention – bays or zones, Fire prevention – bays or zones: To pr...

Fire prevention – bays or zones: To prevent the spread of a fire within an aircraft/engine nacelle, it is divided up into sections or zones, each being separated by a fireproof

Aviation legislation - Variant Aircraft, Variant Aircraft A variant air...

Variant Aircraft A variant aircraft is one that embodies certain design features which differ from one for which a Certificate of Airworthiness (C of A) has previously been iss

Matlab, load flow analysis by fast decoupled method

load flow analysis by fast decoupled method

Feathering the propeller, Feathering the propeller: If there is an engi...

Feathering the propeller: If there is an engine failure in flight, the propeller would windmill creating drag and increasing any damage that had occurred in the engine. Feathe

Difference between elastic and plastic deformation, Q. State difference bet...

Q. State difference between elastic and plastic deformation. Ans. Elastic deformation: Elastic deformation is that the part of the deformed material, when the applied load is

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd