Characteristics of computer controlled scheduling (ccs), Mechanical Engineering

Assignment Help:

Characteristics  Of  Computer  Controlled Scheduling (Ccs)

To control the manufacturing system in an effectual way, the system is normally composed in a task-based hierarchy. The hierarchy contains five levels and is demonstrated in figure. At The lowest level of the system, the system contains physical machining equipment. Workstation equipment gives integration and interface functions for the equipment and it that resides just above the process level.

This must be noted in various existing models that several of the above assumptions are partially relaxed. For the illustration, the literature on parallel machine scheduling studies the work centers which comprise m processors that may be capable to process m jobs simultaneously.

                                                 344_Characteristics  Of  Computer  Controlled Scheduling (Ccs).png

                                                                      Figure: Control Hierarchy

Within computer controlled Scheduling models, all the equipments should explicitly identify under the supervisory computer control. This comprises machines, auxiliary stations, material handlers, and restricted capacity storage space. The individuality of the CCS problem originates mostly from the following figure as given below:

  • Usual resource models;
  • Part contact states;
  • Deadlocking;
  • Dynamic machine routing;

                                  1509_Characteristics  Of  Computer  Controlled Scheduling (Ccs) 1.png

 

                                           Figure: Originators of Uniqueness of CCS Problem

The forementioned characteristics are described below.


Related Discussions:- Characteristics of computer controlled scheduling (ccs)

What is boiler feedwater, Q. What is Boiler feedwater? The boiler feedw...

Q. What is Boiler feedwater? The boiler feedwater will be a mixture of desalinated water, treated make-up water and returned condensate, deaerated and heated, supplied by other

Voltage -fundamentals of electricity , Voltage: The voltage is the potent...

Voltage: The voltage is the potential difference between two points. The current flows from higher potential to lower potential. Voltage is measured in volts (V). V = IR

Working principle of ignition system , Working Principle of Ignition System...

Working Principle of Ignition System: An alternating current (AC) is generated when a magnet moves between two stationary coils. In a magneto, a coil of wires moves between two m

Design equipment rooms for plant, Q. Design Equipment Rooms for plant? ...

Q. Design Equipment Rooms for plant? Equipment for important safety systems and controls shall be located such that they can remain operational during the defined accidental ev

Determine the brake power of an engine, Determine the Brake power of an Eng...

Determine the Brake power of an Engine which is running at a fixed speed of 300 r.p.m. and carries a rope brake Dynamometer. The Dead weight on the spring balance and engine readin

Thermodynamics, Convert the following readings of pressure to KPa absolute,...

Convert the following readings of pressure to KPa absolute, assuming that the barometer reads 760mm Hg: (a) 100 psig, (b) 8in. Hg vacuum, and (c) 76in Hg gage.

Differences between torque and torsion, Differences between torque and tors...

Differences between torque and torsion: Give differences between torque and torsion. List a few examples of torsion in the engineering practice. Sol.: When structural or

Ratio of belt tension - open belt drive, Ratio of belt tension: For Op...

Ratio of belt tension: For Open belt drive:   Angle of contact (θ) for larger pulley = ∏ + 2α Angle of contact (θ) for smaller pulley = ∏ - 2α For cross belt drive:

Marshalling yard, Marshalling Yard: Function The marshalling ...

Marshalling Yard: Function The marshalling yard is a facility where goods wagons are sorted out for being dispatched to different stations. After being sorted out, th

Cross drainage works, Cross Drainage Works: Culverts A large ...

Cross Drainage Works: Culverts A large number of culverts are needed for taking care of the streams crossing the railway lines. The culverts can be one of the followi

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd