When analyzing a truss using the method of sections to find

Assignment Help Civil Engineering
Reference no: EM13531083

When analyzing a truss using the method of sections to find theforces in specific members. What is a good strategy to helpdecide where to make the cuts to separate the truss into separate sections?

Reference no: EM13531083

Previous Q& A

  Determine the final speed of the cart

Two men A and B, each having a weight of 160lb stand on a200lb cart. Each runs with a speed of 3ft/s measured relativeto the cart. Determine the final speed of the cart if:

  How much flow human lung can deliver cold soda and/or water

One hundre cubic meter of gas at-34.6c celcius and 200kpa in absolute pressure is compressed to a volume of 25 cubic meter and  an absolute pressure of 1000kpa. what is the new temperature, in degrees celsius?

  Fresh water fish do not survive in water

If the concentration of glucose in plasma is 5 mM, and theintracellular glucose concentration is negligible (i.e. 0 mM), whatis the rate of glucose diffusion (J) into the cell? Assume that thethickness of the plasma membrane is 10 nm.

  What safety factor will be necessary to allow an extraction

A lead-zinc mine is to be developed by a room-and-pillar layout.  The mine is located at a depth of 500ft, the overlying rock has an average specific gravity of 2.56, and the pillar rock wast tested and found to have a

  What is the composition of the last solid remaining prior

What is the composition of the last solid remaining prior tocomplete melting?

  Determine the concentration of carbon in this alloy

The microstructure of an iron-carbon alloy consistsof proeutectoid ferrite and pearlite; the mass fractions of thesetwo microconstituents are 0.174 and 0.826, respectively. Determinethe concentration of carbon in this alloy.

  What must be its composition if this is notpossible

It is desirable to produce a copper-nickel alloythat has a minimum noncold-worked tensile strength of 380 MPa(55,000 psi) and a ductility of at least 45% EL. Is such an alloypossible? If so, what must be its composition? If this is notpossible, then ..

  What is the composition of the ß phase

A hypothetical A-B alloy of composition 40 wt%B-60 wt%A at sometemperature is found to consist of mass fractions of 0.66 and 0.34for the αand β phases, respectively. If the composition of the α phase is 13 wt% B-87 wt% A, what is the composition ofth..

  What types of proteins had to have been degraded to isolate

What types of proteins had to have been degraded to isolate theDNA? Why is DNA considered to be an acid?

  What is the total lenth ac and its standard deviation

A line AC was observed in 2 sections AB and BC, with lengthsand standard deviations listed below. What is the total lenth AC and its standard deviation?

Reviews

Write a Review

 

Similar Q& A

  Determine the dead uniform load in kips per linear foot

A wide flange steel beam supports a permanent concrete masonry wall, floor slab; architectural finishes mechanical and electrical systems. Determine the dead uniform load in kips per linear foot acting on the beam.

  What pressure in mpa must be applied to water to reduce

At 25 C, approximately what pressure in MPa must be applied to water to reduce its volume by 2%

  Determine the concentration of ubod in the effluent

If the length of the river connection between the two lakes is equal to 3km and the velocity in the river is equal to 0.4 m/s, determine the concentration of UBOD in the effluent from the second lake.

  Determine perpetual equivalent annual worth at interest rate

The cash flow associated with landscaping and maintaining a certain monument in Washington, D.C., is $100,000 now and $50,000 every 5 years forever. Determine its perpetual equivalent annual worth (in years 1 through infinity)

  Calculate the volume of a cylinder that contains 60 lbm

Calculate the volume of a cylinder that contains 60 lbm of carbon dioxide at 230°F and 23 psig pressure. Assume atmospheric pressure to be 14.7 psia.^4

  Determine the mass flow rate of the cooling water

refrigerant 134a is compressed at steady state from 2.4 bar, 0 degrees celcius, to 12 bar, 50 degrees celcius. Refrigerant enters the compressor with a volumetric flow rate of 0.38m^3/min, and the power input to the compressor is 2.6 kW.

  Calculate the pressure in the constriction in a pipe

When 0.3 m^3/s water flows through a 150 mm constriction in a 300 mm horizontal pipeline, the pressure at a point in the pipe is 345 kPa, and the head loss between this point and the constriction is 3 m.

  What is velocity in the channel before the hydraulic jump

Water flows uniformly at a depth of y1 = 40 cm in the rectangular troweled concrete channel shown, which is 10 m wide and has a bed slope of So = 0.040 . What is the velocity in the channel before the hydraulic jump

  Explain each of the parametersin the equation is obtained

According to barton(1974) the quality of a given rock mass can bedetermined using the equation below. explain each of the parametersin the equation is obtained.

  Find the conjugate depth to an initial flow depth

A trapezoidal channel having bottom width of 8 m and side slopes of 1 : 1, carries a discharge of 80 m^3/s. Find the conjugate depth to an initial flow depth of 0.75 m before the jump.

  Discuss 2 elements of an expensive gps rec in relation

We have a good sense of the fact the increased accuracy comes at a very increased price. Discuss 2 elements of an expensive GPS REC in relation to an inexpensive GPS REC.

  Determine the power produced by the turbine

A Rankine cycle has a boiler pressure of 2500 psi and a condenser pressure of 1psi. The temperature at the inlet of the turbine is 800F. The turbine has an isentropic efficiency of 90 percent and the pump operates isentropically.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd