What would be the resultant force on the plate

Assignment Help Civil Engineering
Reference no: EM13543407

1.Use the conjugate beam method and determine the slope and displacement at the end C of the beam. E=200 GPa, I=70(10^6)MM^4

2.Water at 50 F is flowing through 80 ft of 4 in diameter of average cast-iron pipe causes a friction head loss of 0.27 ft. find the flow rate.

3.A 40-mm-diameter jet has a velocity of 25 m/s. If this jet were to strike a large flat plate normally, what would be the resultant force on the plate?

Reference no: EM13543407

Questions Cloud

Explain the difference between materials considered to have : Explain the difference between materials considered to have “homogeneous” and “isotropic” material properties. Give examples of materials that are considered isotropic but not homogeneous and others that are considered homogeneous and anisotropic.
Determine the initial and final temperatures : A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 125 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase
Determine the heat loss or gain during this process : A piston-cylinder device contains helium gas initially at 150 kPa, 20 degrees C, and 0.5 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.
What is the magnitude and direction of the resultant force : Water under a gage pressure of 350kPa flows with a velocity of 5 m/s through a right-angled bend that has a uniform diameter of 250 mm
What would be the resultant force on the plate : A 40-mm-diameter jet has a velocity of 25 m/s. If this jet were to strike a large flat plate normally, what would be the resultant force on the plate?
Determine at that instant the radial and transverse compont : 1.5-kg collar is attached to a spring and slides without friction along a circular rod in a vertical plane. Knowing that the tension in the spring is70 N and the speed of the collar is 3.8 m/s as it passes through point A,
Find the pressure at the forward and rear corners along the : A closed box with horizontal base 6m x 6m and height of 2m is half-filled with water and is accelerated Ax=4.9 m/sec^2 and Ay=-2.4 m/sec. find the pressure at the forward and rear corners along the bottom.
Draw the influence line for the tension in the cable as : Draw the influence line for the tension in the cable as a point load travels across the beam. Find the maximum tension in the cable due to a live point load of 6 k on the beam.
Determine the adjusted asd values associated with the : A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D + S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Find expected error l if odolite has direct angular accuracy

Calculate expected error L if a theodolite has direct angular accuracy of 10" and a distance of 1500m was measured.

  What is shear rate in water in sliding and standing plates

What is the shear rate in the water between a sliding and standing plate, if V = 10 ft/s is the moving plate velocity and 0.1 in. is the distance between the plates

  Calculate the f per m ration for the aeration tank

An activated sludge process receives 4000m^3 / day containing 120 mg BOD /L from the primary settling tank and 3500 m^3/day Containing 25mg BOD/L from the secondary settling tank.

  Find the final temperature and the amount of work

Air can be assumed as a di-atomic ideal gas. Find the final temperature and the amount of work ( in kW) required for air compression at a rate of 100 mol/s , from an initial condition of 1 bar an 25 C to 10 bar; for the following ways.

  What is the flow rate between 2 open storage tanks

Water flows through 800 feet of 12-inch diameter iron pipe (g = 0.0018 inches) between 2 open storage tanks, whose water surface elevation difference is 16 feet. The pipe entrance is flush and square edged

  Find area of steel reinforcement required for concrete tbeam

Find the area of steel reinforcement required for a concrete T-beam for the following data; f'c = 3 ksi, fy=50 ksi,d=28 in, t= 6 in., bw= 16 in., bf= 60 in., and the section sustains a factored bending moment of Mu=360 kip ft

  Calculate the magnitude of the total force supported

The uniform 4 meter boom has a mass of 60 kg and is pivoted to the back of the truck at A and secured by a cable at C. Calculate the magnitude of the total force supported by the connection at A

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  Determine suitable footing dimensions to suit the bearing

Determine suitable footing dimensions to suit the bearing capacity of 100kPa with a factor of safety 2.4

  Design the mosteconomical truss that will support the load

A bridge having a horizontal top cord is span between tow piers Aand B having an arbitrary height. It is required that apin-connected truss be used, consisting of steel members boltedtogether to steel gusset plates. The end supports are assumed to be..

  Calculate molar concentration of metal ion in stock solution

calculate the: 1) molar concentration of metal ion in the stock coagulant solution; 2) coagulant feed rate (into the process water flow stream) in units of L/day and L/min; 3) alkalinity consumed (in the process water flow stream) in units of mg/L..

  Calculate the upward acceleration of the particle

A particle of mass 200kg is lifted up vertically by a force of 104N. Assuming the acceleration due to gravity is 10meterper.secondsquare, write a program to calculate the upward acceleration of the particle.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd