Determine the adjusted asd values associated with the

Assignment Help Civil Engineering
Reference no: EM13543403

A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D + S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.

1. Sketch the beam and the cross section. Show calculations to verify the section properties Sx, and Ix for the member, and compare with the NDS Supplement Table 1C.

2. Determine the adjusted ASD values associated with the section properties in part 1. These include Fbx+’, Fvx’ and Ex’.

3. Repeat part 2 except the moisture content (MC) of the member exceeds 16%

Reference no: EM13543403

Questions Cloud

What would be the resultant force on the plate : A 40-mm-diameter jet has a velocity of 25 m/s. If this jet were to strike a large flat plate normally, what would be the resultant force on the plate?
Determine at that instant the radial and transverse compont : 1.5-kg collar is attached to a spring and slides without friction along a circular rod in a vertical plane. Knowing that the tension in the spring is70 N and the speed of the collar is 3.8 m/s as it passes through point A,
Find the pressure at the forward and rear corners along the : A closed box with horizontal base 6m x 6m and height of 2m is half-filled with water and is accelerated Ax=4.9 m/sec^2 and Ay=-2.4 m/sec. find the pressure at the forward and rear corners along the bottom.
Draw the influence line for the tension in the cable as : Draw the influence line for the tension in the cable as a point load travels across the beam. Find the maximum tension in the cable due to a live point load of 6 k on the beam.
Determine the adjusted asd values associated with the : A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D + S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.
What would be the values of density and water content if the : A soil has a bulk density of 1.91 Mg/m^3 and a water content of 9.5%. The value of Gs is 2.70. Calculate the void ratio and degree of saturation of the soil. What would be the values of density and water content if the soil were fully saturated at th..
Calculate also the unit weight and water content at a degree : Calculate the dry unit weight, the saturated unit weight and the buoyant unit weight of a soil having a void ratio of 0.70 and a value of Gs of 2.72. Calculate also the unit weight and water content at a degree of saturation of 75%.
Determine the density index of the sand : The in-situ dry density of a sand is 1.72 Mg/m^3 . The maximum and minimum dry densities, determined by standard laboratory tests, are 1.81 and 1.54 Mg/m^3, respectively. Determine the density index of the sand.
Is there any appreciable advantage to placing the drains : Within a field that is used for agricultural production, a clay unit is found at a depth 8ft below the land surface. the surface soil has a hydraulic conductivity of .6 ft/d. if parallel drains are placed 2 in per day

Reviews

Write a Review

Civil Engineering Questions & Answers

  Derive the equation for a slightly compressible fluid

Assume that there is only one phase present and that the formation is homogeneous, but anisotropic. Further, assume that viscosity, formation volume factor, and the areas available for flow are constant spatially. Last, assume 3-D flow using x, y,..

  Determine if driver can clear the intersection safely

Assume that the width of the intersection in 24 ft and the car is 20 ft long. If the driver's perception-reaction time is 0.75 seconds, determine if he can clear the intersection safely for the following conditions

  How to draw and label a flowchart for the system

The temperature of steam at the inlets of both turbines is 500 C, and the enthalpy of steam is 3027 kJ/kg at the exit of high pressure turbine, and 2385 kJ/kg at the exti of the low pressure turbine.

  Elevation and stationing of the low point

A 1600 ft long sag verical curve (equal tangent) has a pvc at station 1200+00 and elevation o 1500 ft. the initial grade is -3.5% and the final grade is 6.5%. determine the elevation and stationing of the low point, pvi and pvt.

  Determine deviation at the top of trajectory caused by wind

A fireworks shell is launched vertically from point A with speed sufficient to reach a maximum altitude of 500ft. A steady horizontal wind causes a constant horizontal acceleration of 0.5ft/sec^2, but does not affect the vertical motion.

  Calculate what will be the total emissions of pm and pm10

emissions from waste oil combustion may be estimated using ap-42 1.11. A small boler is operated from 10/15/2012 through 4/15/2013 and it is used to burn 45 gallons per hour of a blended waste oil having an ash content of 7%

  Do any of the three wells exceed the 44 ppm level

Nitrate concentrations are often recorded in units of NO3--N/L to be compared with other nitrogen constituents. Near three rural wells nitrate concentrations were reported as 0.25 mg

  Calculate the mass emissions rate of no2 in kg/day

Assuming that the average stack gas velocity is 10.0 m/s and stack is circular with a 3.0 meter diameter, calculate the mass emissions rate of NO2 in kg/day.

  Discuss the role water conditions plays in the planning

Construction dewatering plays are very large role in the todays construction arena. Discuss the role water conditions plays in the planning and design of a temporary earth support system.

  What formula and information is needed to find the maximum

What is the formula to find the Maximum pressure on a form, and what information is needed to find the maximum pressure on the form?

  Determine what is the offset at the midpoint on the curve

a vertical curve with grade1= 3.6% meets the exit grade of -4.7% at PVI located at station 26.50. A vertical curve of 700 feet is propsed to provide the transition between the two grades.

  Property of sanstone and of the quartzite

if you had a choice of three kinds of aggregate--a sandstone,a crushed basalt,and a quartizite,you may select the basalt.Give one possible characteristic or property of sanstone and of the quartzite that made you decide not to select it for your c..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd