What is the volume of the iron in the entire paper clip

Assignment Help Civil Engineering
Reference no: EM13561390

A typical paper clip weighs 0.59 gram and consists of BCC Iron. The density of iron is 7.87 gram/cm3 and its atomic radius is 0.124 nm.

What is the volume of a unit cell in (nm)3?

What is the volume of a unit cell in cm3?

What is the volume of the iron in the entire paper clip in cm3?

How many unit cells are contained in the paper clip?

How many iron atoms are contained in the paper clip?

Reference no: EM13561390

Questions Cloud

How many feet of head must the pump add to achieve : At a pumped storage facility, water is pumped from a large reservoir to a point 150 feet above the resevoir. How many feet of head must the pump add to achieve
What is the life question the story presents : What is the life question the story presents - How does the story support/point to the answer of the life question?
Calculate the fluid velocities at the two ends : Assume frictionless flow in a long, horizontal, conical pipe. The diameter is 12 inches at one end and 6 inches at the other. The pressure head at the smaller end is 16 feet of water. If water flows through this cone
Calculate the final stable discharge pressure after the pump : Given a variable speed centrifugal pump initially pumping 32,000 pounds mass per hour (lbm/hr) at a discharge pressure of 35 pounds per square inch, gauge (psig), calculate the final, stable discharge pressure after the pump speed is raised by 50%. S..
What is the volume of the iron in the entire paper clip : A typical paper clip weighs 0.59 gram and consists of BCC Iron. The density of iron is 7.87 gram/cm3 and its atomic radius is 0.124 nm.
Estimate what is the electrons speed : Two large conducting plates are connected to opposite poles of a 12-volt battery. What is the electron's speed when it reaches the positive plate
Draw and explain a pump curve that illustrates the effect : Draw and explain a pump curve that illustrates the effect of throttling in the CLOSED direction (i.e., reducing flow) the discharge valve for a constant speed centrifugal pump installed in a cooling water system.
Determine the discharge coefficient for the nozzle meter : An unknown fluid flows through a horizontal 35-mm-diameter pipe with a Reynolds number of 100,000 and a density of 680 kg/m3. The pressure drop across a 21-mm-diameter nozzle meter placed in the pipe is 4.2 kPa.
Calculate the mass flowrate in kg/s of methane that initialy : A tank containing methane has a pressure of 600 kPa and is sitting outside where the air temperature is 20?C. A careless hunter shots a bullet from a rifle that hits the tank. Assuming the resulting hole acts like an isentropic converging nozzle with..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the so2 concentration at a sampling point located

If the effective stack height of the plant is 100 m, and the ground reflects the SO2 emission perfectly what is the SO2 concentration at a sampling point located 2 m above the ground in the town.

  Compute the required weight of coarse aggregate per cubic

A concrete mix with a 3-inch slump, w/c ratio of 0.50 and a sand with a fine modulus of 2.4 contains 1700 lb/cubic yard of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.

  Estimate of the point load strength index

Estimate of the point load strength index Is(50) and suggest a realistic range for the Youngs modulus E.

  Find specific weight and total moisture content of sample

A sample of dry sand with a specific gravity total of 16.49 kN/m3 and a relative density of 2.67 grains, is placed outdoors. During a rainy period, the sample volume remains constant but the degree of saturation increases to 40%.

  Determine the maximum design shear force for the loading

A simply supported span of 28 feet must carry a uniform loading that produces a total factored maximum moment of 300 K-ft including the beam weight. The concrete can be 3.5 ksi and the steel is grade 60.

  Determine the angular velocity of link bc at the instant

If rod slides along the horizontal slot with a velocity of 44 ft/s , determine the angular velocity of link BC at the instant

  Evaluate the pressure head at point

Evaluate the pressure head at point a and determine the vertical effective stress at point b and evaluate the lateral pressurein the brown clay

  Calculate the linear misclosure and relative precision

Balance by the compass rule the departures and latitudes listed in the following closed-polygon traverse. Calculate the linear misclosure, relative precision, and adjusted lengths and bearings

  Determine the design strength for lrfd as a column

An HSS 10×6×5?16 with Fy = 46 ksi is used as a column. The length is 16 feet. Both ends are pinned, and there is support against weak axis buckling at a point 6 feet from the top. Determine the design strength for LRFD.

  Determine what is demand for time if left turns are provided

Given the following geometry of an intersection: Four lanes fornorth and southbound traffic; two lanes for east and west boundtraffic. The peak hour volume for: northbound traffic is 1400vehicles with 10% left and right turns,

  How much water would it yield if water declined uniformly

A confined aquifer has a specific storage of 2.5*10^-6 ft^-1 and a thickness of 200 ft. How much water would it yield if the water declined 5.5 ft uniformly over a circular area with a radius of 1000 ft

  Calculate the absolute pressure head and the gage pressure

The pressure in the steam condenser of a nuclear power plant is 1 psia. Calculate the absolute pressure head, the gage pressure, the gage pressure head, the vacuum pressure, and the vacuum pressure head under standard conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd