Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Given a variable speed centrifugal pump initially pumping 32,000 pounds mass per hour (lbm/hr) at a discharge pressure of 35 pounds per square inch, gauge (psig), calculate the final, stable discharge pressure after the pump speed is raised by 50%. Show all work.
2.Water enters a pipe at 100 psig and 70 degrees F. The density of water under these conditions is 62.3 lbm/ft^3. The pipe has an inside diameter of 4.5 inches. The mass flow rate of the water is measured to be 7500 lbm/hr. What is the fluid velocity in the pipe in feet per second? State all assumptions. Show all of your work.
each wire has a tension of 1kN and is inclined at 45 degree to the vertical. calculate the increase in vertical stress at a depth 1 m below the surface and the amount of elastic settlement below the axis of the pole if E = 40 Mpa and v=0.45
A barge measures 10 ft (depth) by 35 ft by 120 ft and weighs 100 U.S. tons. The barge floats in fresh water (specific weight = 62.4 lb/ft3) and is evenly filled with 38,000 bushels of corn (60 lb/bushel).
A weightless piston is placed on the liquid surface and the water level stabilizes (also in the small tube) to a level of h. Next, a weight of 10 kg is placed on the piston causing the liquid in the small tube to rise.
The two upper lengths of the welded Y-shaped assembly of uniform slender rods have a mass per unit length of 0.3 kg/m, while the lower length has a mass of 0.7 kg/m. Locate the mass center of the assembly. lenghts of all rods aew 30mm
A 40 cm diameter well has been constructed in a water-table aquifer. A pump capable of continuous discharge at 600 m3/day has been installed to test the well. Observation wells are located 10 meter and 50 meters from the pumped well. After pumping co..
The pins on the frame at B and C each have a diameter of 0.25 in. If these pins are subjected to double shear, determine the average shear stress in each pin.
In one observation well water stands 28.8 ft above the bottom at a radius of 687 ft, and in the other it stands 22.5 ft above the bottom. What is the discharge per 100 foot wide strip of the aquifer in square ft per day
The concentration of ammonia is 6 mg/L at one point in the river. If the first - order decay coefficient for the conversion of ammonia to nitrate is 0.05 day-1, what will the ammonia concentration be 10 miles downstream.
The tangent function is defined as than (t)=sin(t)/cos(t). This expression can be evaluated to solve for the tangent as long as the magnitude of cos(t) is not too near to 0
It is expected that 95% saturation will be attained. Calculate the volume of soil that will be needed if the void ratio of the fill material is 1.3
Determine the force required to lift the block of stone that weighs 200 lb. The rollers are frictionless and the static coefficient between all other surfaces is 0.3. Neglect the size and weight of the wedges.
A tension specimen has a gauge length of 8 inches and a diameter of .505 inches. A load of 9580 pounds was found to develope a stress in the specimen equal to the proportional limit of materials. ( assume that the proportional limit and the yield ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd