What is the volume and base diameter of the resulting

Assignment Help Civil Engineering
Reference no: EM13559296

Soil falls from a conveyor belt into a cone shaped pile at a rate of 1000lb/min. The bulk density of the soil is 110lb/ft^3. The height of the pile is equal to the base diameter. What is the volume and base diameter of the resulting pile at five minute intervals up to 1 hour? Record the equations were used to find the results.

Reference no: EM13559296

Questions Cloud

Calculate the low point of the curve if the intersection at : A vertical parabolic curve is to be used as a sag curve, and it is desired to know the location and elevation of the low point. The curve is 750ft long , and the minus grade of 3.6 percent intersects the plus grade of 6.2 percent at station
What is the rotor''s angular velocity one minute after : The rotor of an electric generator is rotating at 200 when the motor is turned off. Due to frictional effects, the angular acceleration of the rotor after the motor is turned off is α=-0.01ω rad/s^2 , where is the angular velocity in rad/s.
Estimate how much coffee has spilled out of the beaker : During an all-night cram session, a student heats up a (0.7 x 10-3 m3) glass (Pyrex) beaker of cold coffee.Initially, the temperature is 18°C, How much coffee(in cubic meters) has spilled out of the beaker
How much would the answer change : A buried horizontal concrete pipe (n=0.012) of unknown length needs to be replaces. the length is not known because the original plans for the pipeline route have been lost.
What is the volume and base diameter of the resulting : Soil falls from a conveyor belt into a cone shaped pile at a rate of 1000lb/min. The bulk density of the soil is 110lb/ft^3. The height of the pile is equal to the base diameter
Determine what is the cost of its operation : a 300 watt toaster is plugged into a 120 volt house current.Electricity is sold at 15 cents per kilowatt hour. If the toasteroperates for 2.5 minutes what is the cost of its operation
How much tangent distance between the two curves is needed : A 6-lane freeway horiz. alignment has a 1200’ C.L. radius going into a tangent and then a reversing 1800’ radius. How much tangent distance between the two curves is needed to meet the superelevation runoff requirements?
Obtain the speed at which the water leaves the hole : A large storage tank, open to the atmosphere at the top and filledwith water, develops a small hole in its side at a point11.0 m below the water level. Determine the speed at which the water leaves the hole
What happens to the reading in the manometer : A pitot-static tube connected to a differential manometer measuring the fluid velocity in a pipe. what happens to the reading in the manometer, h, if the fluid velocity in the pipe is halved?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the time required to bring the train to a stop

The subway train shown is traveling at a speed of 30 mi/hr in the west direction when the brakes are fully applied on the wheels of cars B and C, causing them to slide on the track, but are not applied on the wheels of car A.

  Determine the time for the log to reach a speed

A truck is hauling a 300-kg log out of a ditch (20 degree incline) using a winch attached to the back of the truck. Knowing the winch applies a constant force of 2500N and the coefficient of kinetic friction between the ground and the log is 0.45

  What is the net upward force exerted

the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?

  Find the maximum shear stress due to the torsional moment

Member ABC is composed of two sections. Section AB has an outside diameter of 60mm and inside diameter of 50mm, whereas section BC is solid. Find the maximum shear stress due to the 1.5kN·m torsional moment applied at B and the 2.0kN·m moment at C..

  Define concentration of pollutant in the effluent leaving

A lagoon with volume 1200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100m^3/day for a long enough time to assume that steady-state conditions apply

  Resultant force from all fluids

A tank is filled with oil (specific gravity 0.8) and water to a depth of 10 meter and 6 meter respectively. Find the resultant force from all fluids acting on the gate of 1.8 meter by 9 meter.

  Determine diameter of rod if it has to be subjected to load

A rod of copper alloy 50 inches long has a modulus of elasticity of 16*10^7 psi. If the maximum allowable elongation is 0.05 in, determine the diameter of the rod if it has to be subjected to a load of 3200 lb.

  Determine the actual detention time observed in the field

Determine the actual detention time observed in the field of two circular settling tanks with depth 3.5 m that was designed to have an overflow rate not exceeding 60 m3/m2-day and a detention time of at least 2 hour.

  Determine the reactor basin volume of the influent bod5

The influent flow is 380 Lpcd and the influent BOD5 is 200 mg/L. Pertinent data are: Primary clarifier removes 33% of the influent BOD5, and the state regulatory agency allows a volumetric loading of 0.48 kg BOD5 /(m3.day). Determine the reactor b..

  Determine by trigonmetry the magnitude and direction

knowing that both members are in compression and that the force is 15 KN in member A and 10 KN in member B, determine by trigonmetry the magnitude and direction of the resultant of the force applied to the bracket by member A and B.

  Determine the design speed of the curve

an equal-tangent sag vertical curve is designed with the PVC AT STation 109 + 00 and elevation 950 ft, the PVI at station 110 + 77 and elevation 947.34ft,and the low point at station 110 + 50 . Determine the design speed of the curve.

  Explain roman technology and engineering

Roman technology and engineering. Technology and engineering were among Rome's most famous achievements. Describe and explain the importance of Roman technology and engineering

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd