User Account

All Pages

What is the ratio of chilled air to warm air

Assignment Help Chemical Engineering
Reference no: EM131172224

A device with no moving parts provides a steady stream of chilled air at 248.15 K (-25°C) and 1 bar. The feed to the device is compressed air at 298.15 K (25°C) and 5 bar. In addition to the stream of chilled air, a second stream of warm air flows from the device at 348.15 K (75°C) and 1 bar. Assuming adiabatic operation, what is the ratio of chilled air to warm air that the device produces? Assume that air is an ideal gas for which Cp = (7/2)R.

Reference no: EM131172224

Questions Cloud

Whether the claimed performance of process is consistent : Determine whether the claimed performance of the process is consistent with the second law. Assume that air is an ideal gas for which Cp = (7/2)R.
Are isentropic processes necessarily reversible : Reversible adiabatic processes are isentropic. Are isentropic processes necessarily reversible and adiabatic? If so, explain why; if not, give an example illustrating the point.
What will happen in the gasoline market if oil prices rise : What will happen in the gasoline market if oil prices rise? What will happen in the cell phone market as technology improvements bring costs down? What will happen in the syrup market if honey prices rise?
Review the operational analysis done through the interview : In the design phase of Fabrics, Inc. Blanchard and Thacker (2013) only developed objectives for conflict resolution. Choose one of the other training requirements and develop three to four learning objectives. Critique the design component and ide..
What is the ratio of chilled air to warm air : Assuming adiabatic operation, what is the ratio of chilled air to warm air that the device produces? Assume that air is an ideal gas for which Cp = (7/2)R.
How would you assess business risk of hih insurance limited : How would you assess the business risk of HIH Insurance Limited? List several inherent risk factors effecting HIH at the financial report level and whether they would have contributed to an increase or decrease in the inherent risk assessment
Determine a numerical value for the ratio of heat : Determine a numerical value for the ratio of heat extracted by the refrigerator ("cooling load") to the heat delivered to the engine ("heating load").
Write business proposal for any organisational issue : Task: Write a business proposal for any significant organisational issue. It could be any hypothetical or real issue in the organisation
What is the total rate of entropy generation in w k-1 : An electric motor under steady load draws 9.7 amperes at 110 volts; it delivers 0.93 Kw of mechanical energy. The temperature of the surroundings is 300 K. What is the total rate of entropy generation in W K-1?

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Could you use the heat from this process to boil water

She believes she can extract 1700 kW of work and 220 kW of heat that will be used to boil water at 1 bar. Her process, whose details are yet to be determined, will receive streams A and B as inlet and will have a single outlet stream that will be ..

  Will the bed of solids on the belt fluidize

Hot air at 150 ºC is blown up through the dryer belt at a volumetric flow rate of 7200 m3 /hr per m2 of belt area. Will the bed of solids on the belt fluidize?

  Is this a maximum boiling or minimum boiling azeotrope

One mol of a solution, whose bubble point at 0.5 bar is 48.3 °C, is mixed with chloroform until the final mixture contains 50% chloroform (by mol). How much chloroform is needed?

  Find the induced emf across the coil

Calculate the average mechanical torque needed to turn the coil and generate power for the resistor. Identify the action of the device as that of a motor or a generator.

  Find the -6 db width of the envelope of a time pulse

Find the -6 dB width of the envelope of a time pulse and the two end frequencies needed to scan a 1 mm thick slice from -15 cm to +15 cm around an isocenter on the z axis. Assume Gz = 0:5 T=m.

  Calculate the size of the current pulse applied

Calculate the size of the current pulse applied at 6 ms for 1 ms, necessary to raise Vm to 40 mV.

  Determine the frequency of the stator-induced voltage

The uniform air gap is of length 1 mm, while the armature diameter is 0.5 m, and the axial length of the machine is 1.5 m. The field winding carries a current of 1 A (dc) and the rotor is driven at 3600 r/min.

  Design variables necessary for sizing equipment

Assist with the setting of design variables necessary for sizing equipment

  What is difference between first and second order kinetics

And if the reactant was in excess to the waste stream and was modeled with 2nd order kinetics equal to k = 1000 g-moles per liter minute --- what does this mean?

  Part-1why fiuids are importantnbspin chemical engineering1

part-1why fiuids are importantnbspin chemical engineering1. enormous number of materials normally exist fias gases or

  Specific heat of superheated steam at 150kpa is 2kj/deg

What diameters of inlet and outlet pipes would be required for a flow of 2270kg per hour with a velocity of 15m/s both before and after the reducing valve?

  Petrol used for petrol engine contain

The petrol used for petrol engine contain, 84% carbon and 16% hydrogen. The air supplied is 80 % of that theoretically required for complete combustion. Assuming that all hydrogen is burnt, and that carbon burns partly to CO and par..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd