What is the power requirement of the compressor

Assignment Help Chemical Engineering
Reference no: EM131172047

Methane is compressed adiabatically in a pipeline pumping station from 3500 kPa and 308.15 K (35°C) to 5500 kPa at the rate of 1.5 kmol s-1. If the compressor efficiency is 0.78, what is the power requirement of the compressor and what is the discharge temperature of the methane?

Reference no: EM131172047

Questions Cloud

Determine the temperature and pressure of the steam : Determine the temperature and pressure of the steam in its intermediate state between the two turbines. What is the overall efficiency of the two turbines together with respect to isentropic expansion of the steam from the initial to the final sta..
Describe your sample and your sampling method : Describe your sample and your sampling method. Explain the four steps of the research process you followed, and define the critical value and the test statistic your analysis provided. Provide the main finding of the study. What did you prove or fa..
What fraction of the steam entering the turbine : what is the thermal efficiency of the cycle and what fraction of the steam entering the turbine is extracted for the feedwater heater?
Example of an project schedule : Hello tutors any one have Microsoft Project 2013. I need a project schedule along with a 1 to 2 page paper. The paper has to be original in your own words. Also I have uploaded the instructions, an example of an project schedule, and my paper for..
What is the power requirement of the compressor : If the compressor efficiency is 0.78, what is the power requirement of the compressor and what is the discharge temperature of the methane?
Show that the thermal efficiency of this cycle : In an optimum countercurrent exchanger, the temperature of the air leaving the compressor is raised to that of point D in Fig. 8.12, and the temperature of the gas leaving the turbine is cooled to that of point B in Fig. 8.12. Show that the therma..
Describe the ccc for your employer or company : For your next post, explain the cash conversion cycle (CCC). Describe the CCC for your employer or company in an industry in which you're interested. What are some specific things that your company could do to decrease your cash conversion cycle
The balanced scorecard and organizational effectiveness : Select an organization to study for this exercise. It should be an organization for which one of you has worked, or it could be part of the university.
What is the velocity of the air leaving the nozzle : If expansion in the nozzle is isentropic and if the nozzle exhausts at 1 bar, what is the pressure at the nozzle inlet (turbine exhaust) and what is the velocity of the air leaving the nozzle?

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Determine blood urea concentration as a function of time

5. A patient is placed on a kidney dialysis unit three times a week. The dialyzer has a membrane area of 1 m2 and is operated in a countercurrent mode. The blood flow rate is 200 ml/min and the dialysate flow rate is 500 ml/min. Membrane permeability..

  What is the vapor fraction when the first liquid boils off

Carbon tetrachloride (1) and water (2) are essentially immiscible liquids. A stream contains 80% CCl4 by mole and the remaining is water.

  Determine the synchronous speed in revolutions per minute

Determine the synchronous speed in revolutions per minute and the useful torque in new ton meters of a 200-hp, 60-Hz, six-pole synchronous motor operating at its rated full load (1 hp ≅ 746 W).

  Average total moisture content

A piece of hemlock wood measuring 15.15 x 14.8 x 0.75 cm is to be dried from the two large faces from an initial total moisture content of 90% to a final average total moisture content of lo%, with drying taking place in the falling-rate period wi..

  Estimate the density of man

A  human being  (75  kg ) consumes about  6000 Kj   of food    per day. Assume  that the food   is all glucose   and  that  overall reaction   is- C6H12O6  +6O2 ------à 6CO2 +6H20  , Δ H= -2816 KJ

  Develop a truth table for turning on the segments

Show a schematic diagram of the seven segment decoder/driver block (available in IC form).

  Calculate the expected photocurrent un der these cond itions

Assume you. have a photodctcctor with a current rcsponsi vity of 5 AJW. A continuous wave HeNe laser with wavelength of 632.8 nm and spot size of 0.5 mm2 is incident on the active area of the detector. Assume that 6.37 x 1021 photons per m..

  Is resolution strongly dependent on lens numerical aperture

What are the main limitations of the resolution of a scanning electron microscope (SEM) image? Is resolution strongly dependent on lens numerical aperture (NA)?

  Determine the maximum layer of the hydrogel membrane

Determine the maximum layer of the hydrogel membrane that would result in an oxygen concentration of at least 1.104 mol/mL everywhere in the capsule.

  Finding reactor size for adiabatic operations

Explain the graphical design procedure for finding the reactor size for adiabatic operations ofPlug flow and Mixed flow reactors.(May-2005 & Dec-2005) and The flowthrougha tubularreactor, inwhicha first order irreversible liquid phase reaction tak..

  Find the power factor and current of the other machine

If one of the machines has its field excitation adjusted such that it delivers 125 A lagging current, determine the armature current, power factor, excitation voltage, and power angle of each machine.

  Define job analysis of a chemical engineer

Job Analysis of a Chemical Engineer, Develop documentation for human resources professionals to manage a specific employment position. The materials you create would assist human resources professionals to choose

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd