What is the optimal life of the forklift in years

Assignment Help Civil Engineering
Reference no: EM13317745

A 2000-pound, counterbalanced, propane forklift can be purchased for $30,000. Due to the intended service use, the forklift's market value drops 20% of its prior year's value in Years 1 and 2 and then declines by 15% until Year 10 when it will have a scrap/market value of $1000. Maintenance of the forklift is $400 per year during Years 1 and 2 while the warranty is in place. In Year 3 it jumps to $750 and increases $200 per year thereafter. What is the optimal life of the forklift (in years)?

Reference no: EM13317745

Questions Cloud

Find the angle through which the drill rotates : A drill starts from rest. After 3.66s of constant angular acceleration, the drill turns at a rate of 2694 rad/a, find the angle through which the drill rotates
What is the solids concentration of primary clarifier sludge : a 20 mgd wastewater treatment plants primary clarifier influent has 800 mg/l solids. the clarifier removes 18 percent of the solids. the sludge flow rate is 0.070 MGD. (a) what is the solids concentration of primary clarifier sludge
Determine what is the euac for each option : Sacramento Cab Company owns several taxis that were purchased for $25,000 each 4 years ago. The cabs' current market value is $12,000 each, and if they are kept for another 6 years they can be sold for $2000 per cab.
Find the minimum euac for machine and its economic life : A machine has an initial cost of $10,000. Its market value declines by 20% annually. The repair costs are covered by a warranty in year 1, and then they increase $600 per year. The firm's MARR is 15%.
What is the optimal life of the forklift in years : Due to the intended service use, the forklift's market value drops 20% of its prior year's value in Years 1 and 2 and then declines by 15% until Year 10 when it will have a scrap/market value of $1000.
Determine soils angle of internal friction under pressure : A triaxial test was performed on a dry, cohesionless soil under confining pressure of 144 kN/m^2. If the sample failed when the deviator stress reached 395.8 kN/m^2, determine the soil's angle of internal friction.
Find the angle through which the part rotates : A machine part rotates at an angular speed of 0.56 rad/s; its speed is then increased to 3.46 rad/s using an angular acceleration of 0.44 rad/s2, Find the angle through which the part rotates
What is the maximum value of the house : What could you do to immunize the pension fund against changes in the interest rate and what are the benefits and drawbacks of this approach in practice? Explain your answer.
Determine the angle of internal friction for the soil : A cohesionless soil sample was subjected to a triaxial test. The sample failed when the minor principal stress (confining pressure) was 1200 lb/ft^2 and the deviator stress was 3000 lb/ft^2.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the speed and acceleration at the instant t

the motorcycle is traveling at 1 m/s when it is at A at the bottom of the ramp. If the speed is then increased at v=0.1 m/s^2, determine its speed and acceleration at the instant t=5s

  Determine void ratio and unit dry weight of soil particles

A 110 cm^3 sample of wet soil has a mass of 106 g and a degree saturation of 100%. When oven-dried, the mass is 81 g. Determine the 1) water content, 2) specific gravity, 3) void ratio, and unit dry weight of soil particles.

  Formulate the shear and bending moment expressions

Show/formulate the shear and bending moment expressions for each board, and plot/draw the shear and bending moment diagrams of the boards.

  Electron and hole motions in a p-n junction

Briefly describe electron and hole motions in a p-n junction for forward and reverse biases; then explain how these lead to rectification.

  What is the main difference of prestressed concrete beams

What is the main difference between the calculation of deflections for reinforced and prestressed concrete beams

  Determine highest bodu concentration possible in effluent

Determine the highest BODu concentration possible in the effluent which can still achieve the permitted requirement of a DO greater than 5 mg/L year round.H =4 m (assume no change due to wastewater flow)

  Determine the power output of the engine in each cycle

If it absorbs 100 Joules each cycle from the hot reservoir, how much work does it do. How much heat is given off in each cycle If each cycle takes 0.5 seconds, find the power output of the engine.

  Develop a simple urban constructed wetland design

Develop a simple urban constructed wetland design.

  Explain how to estimate the diameter of the small pipe

Fluid flows steadily, at a volume rate Q, through a large pipe and then divides into two small pipes, the larger of which has an inside diameter of 25 mm and carries three times the flow of the smaller pipe.

  Determining axial load of a dense sand

A dense sand has an effective friction angle of 43 and c'=0. A dry, 2.8-inch diameter sample is tested in drained triaxial shear with a confining pressure of 2500 psf. What axial load, P (in pounds), will be required to fail the sample?

  Determine the peak discharge that would result no ponds

Suppose a drainage basin has an area of 288 acres with a CN=55(Runoff Coef. of 0.30). Determine the peak discharge (in cfs) that would result from a 6.0in., 24-hr assuming there are no ponds and swampy areas.

  Determine percent error in replacing sine and tangent angles

Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd