What is the minimum l/g that you would approve

Assignment Help Civil Engineering
Reference no: EM13536725

A company has submitted plans for a hydrogen sulfide (H2S) scrubber.H2S is to be removed from the waste air discharge by scrubbing with a dilute: triethanolamine-water solution in a packed tower at atmospheric pressure. Specification indicate that the gas flow rate is 10,000 acfma at 70F and contains 15,000 ppm H2S. The inlet liquid is to be solute-free. The H2S must be reduced to 500 ppmv. The pilot plant data indicate that Henery's Law applies (H= 2.0 mole fraction in air/mole fraction in liquid) and that HTU (Height of Transfer Unit) is 1.94 ft. The company proposes to install a 5- ft diameter, 10ft high packed tower.

(a) What is the minimum L/G (gal/1000ft^3) that you would approve?

(b) If the tower is operated at 80.65 lb molesof scrubbing liquid per minute,is it adequate?

Reference no: EM13536725

Questions Cloud

Where the function changes a lot or where the function : As a further exercise, try to find values of t for your approximation that keeps the error (i.e., the difference between the approximation and the real function v(t) ) less than 0.1.Hint: to help with this, ask yourself this question: where would mor..
Determine the maximum torsional stress in the shaft and its : The propellers of a ship are connected to an A-36 steel shaft that is 60m long and has an outer diameter of 340mm and inner diameter of 260mm
What is the latitude of your location : Draw an inverted bowl – i.e., a horizontal line (exactly 10 inches long), with a big semi-circular upside-down “U” connecting the ends of that horizontal line. This is a picture of the ground and sky. Draw a little tiny person (you) at the mid-point ..
What possible corrective actions could have been implemented : For Hartford civic center roof collapse disaster. What possible corrective actions could have been implemented to prevent this failure? explain in your own words.
What is the minimum l/g that you would approve : A company has submitted plans for a hydrogen sulfide (H2S) scrubber.H2S is to be removed from the waste air discharge by scrubbing with a dilute
Calculate the settling velocity of a spherical particle : Use Stoke’s Law to calculate the settling velocity (m/s) of a spherical particle with a diameter of 1.0 mm and a density of 3 g/mL in water at a temperature of 30?C. The dynamic viscosity of water at 30?C is 0.798 x 10-3 N s/m2. The density of water ..
Compute the flows with return periods of 1 5 and 15 years : The table below provides the flows for the Llano River in Texas for the period of 1951 to 1970. Using the simplified frequency analysis method show in class (Weibul method)
What the average power usage of the average american : The U.S. accounts for just about one-quarter of all of the energy used by people on earth, and has some 300 million people. What’s the average power usage of the average American?
Calculate the concentration of methanol in the exit gases : You have a stream of air containing methanol at 5% by volume. The stream is flowing at 2000 actual ft^3/min at 1 atm pressure and 110 F. The regulations require94% removal of the methanol, and you decide to try a water absorption column, using pure w..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine approximately what the ratio of the density of air

Consider an air bubble rising from the bottom of a lake. Neglecting surface tension, determine approximately what the ratio of the density of the air in the bubble will be at a depth of 34ft to its density at a depth of 8 ft

  Determine the maximum allowable uniform load what

A W410 X 0.83 steel section is used in a10 m simple span. Determine the maximum allowable uniform load what the beam can carry if the allowable flexural stress is 165MPa, the allowable shear stress is 100 MPa, and the allowable deflection is 1/360 of..

  Expanded depth of the bed after the backwash

Find the expanded depth of the bed after the backwash when initial depth of the bed is 3 ft using given conditions. μ = 0.01g/cm/sec, T = 25oC, ρs = 2.65, ρ=1, washrate = 1.5 cm/sec, ks2 = 196. (Assumed single size)

  Compute relative compaction based on modified proctor test

sand cone test has been performed . The test results: intial weight of cone + sand =13.51lb, Final weight of sand cone + sand= 4.26lb, weight of sand to fill cone=2.12lb, weight of soil from hole+bucket=12.42lb, weight of bucket=1.21lb

  By what mechanisms can soil be lost from the resulting solid

A waste mixture contains a variety of volatile organic compounds, nonvolatile organics, metals, and sandy soil. In a vitrification treatment, a. which of these materials are likely to be retained in the resulting solid

  Explain the meaning of the reliability index ß

Explain the meaning of the reliability index,β, and how it relates to failure / survival inthe context of bridge design? What is the value ofβ we use in design?

  Assist structural engineer for a bridge replacement project

You should provide the structural engineer with a formal typed report that will include all of your analyses and final size of the footing. You should also include all of your design assumptions in your report.

  What type of system would you classify an electric wire

A system consists of a gas confined between a cylinder and piston such that work and heat may cross the boundary. What type of system is that. What type of system is a free body as used in mechanics or civil engineering.

  What value for fy are two forces perpendicular to each other

what value for Fy are the two forces F1=4i+Fyj+20K(N) and F2=8i-5j+7k(N) perpendicular to each other

  What is the smallest number of bulbs to be purchased

A company manufactures a brand of light bulbs with a lifetime in month that is normally distribute with a mean=3 and a variance=1. A consumer buys a number of these bulbs with the intention of replacing them successively as they burn out.

  How much water horsepower is required to pump the head

how much water horsepower is required to pump 380 gpm against a total head of 420 feet. If the efficiency in the above problem is 85 percent and the pump efficiency is 80 percent. Calculate the required horsepower.

  What average force was exerted on the ball

After falling from rest from a height of 32 m, a 0.45 kg ball rebounds upward, reaching a height of 22 m. If the contact between ball and ground lasted 1.5 ms, what average force was exerted on the ball?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd