What is the maximum internal pressure in cylindrical vessel

Assignment Help Civil Engineering
Reference no: EM13308048

A cylindrical pressure vessel can support an internal pressure of 2640 psi. The maximum hoop stress is (65000/2) psi and the maximum shear stress is 16000 psi. If the diameter of the tank is 7 inches,what is the minimum wall thickness. If the wall thickness is 0.25 in,what is the maximum internal pressure?

Reference no: EM13308048

Questions Cloud

State a c program that opens the file : Write a C program that opens the file and firstly stores all the values in an appropriately declared two-dimensional array of integers. It then should analyse this array to find (from the 40 input values) the total number of coursework marks in the..
Determine the maximum stress and strain in the ball : A rubber ball is inflated to a pressure of 65 kPa .At that pressure the diameter of the ball is 240mm and the wall thickness is 1.25 mm.The rubber has a modulus of elasticity E of 3.6 Mpa and a poisoon'd ratio of 0.48.
Determine the normal and shear stresses acting on an angle : A pressurized steel tank has a radius r=0.6m, a wall thickness t=18mm and an internal pressure p of 2.8 MPa.The steel has a modulus of elasticity E of 200 GP and a poissons ratio 0.30.
Determine the minimum thickness t of the wall of the tank : A cylindrical tank having a diameter d=2.5 inches is sunjected to internal gas presuure p=600 psi and an external tensile load T=1000 lbs. Determine the minimum thickness t of the wall of the tank
What is the maximum internal pressure in cylindrical vessel : The maximum hoop stress is (65000/2) psi and the maximum shear stress is 16000 psi. If the diameter of the tank is 7 inches,what is the minimum wall thickness.
Find the position vector of the projectile : A projectile is shot from the edge of a cliff 125 m above the ground level with an initial speed of 65.0 m/s at an angle of 37 degree above th horizontal. find the position vector of the projectile when it reaches it maximum height above the top of..
Describe the new product : Describe the new product.
What is the initial acceleration of the block up the ramp : A 1kg block at the bottom of a ramp is on a compressed spring with the spring constant k=300N/m. what is the initial acceleration of the block up the ramp
What is the accleration of the boats : A tugboat pulls two barges with a force of 3000N. The water slows each of the boats with a force of 200N (3 total forces of 200N each). what is the accleration of the boats

Reviews

Write a Review

Civil Engineering Questions & Answers

  How many kilograms each of pearlite

how many kilograms each of pearlite and preutectoid phase form? schematically sketch and label the resulting microstructure

  What is the probability that the vehicle pulling out

what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?

  Determine what is the four lane freeways aadt

A four lane freeway (two lanes in each direction) operates at capacity during the peak hour. It has 11-ft lanes, 4-ft shoulders, and there are three ramps within three miles upstream of the segment midpoint and four ramps within three miles downst..

  What will be the new level of service

If an additional 11ft lane is added (each direction) and all other factors stay the same, what will be the new level of service?

  Does the ph of beverage remain the same or increase

When you allow a can of carbonated beverage to sit open so that the carbon dioxide is released to the air, does the pH of beverage remain the same, increase, or decrease Why

  What is maximum acceleration from rest for car with engine

The car weights 2450 lb, the mechanical efficiency of the drivetrain is 90%, and the wheel radius is 14 inches. The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque.

  Compute the shear modulus for the aluminum

The elastic portion of the tension stress-strain diagram for an aluminum alloy. The specimen used for the test has a gauge length of 2 in and a diameter of 0.5 in. When the applied load is 9 kips, the new diameter of the specimen is 0.49935 in.

  Determine what is the required pipe size to deliver

A concrete pipeline is installed to deliver 6m^3/sec of water (10degressC) between two reservoirs 17 km apart. If the elevation difference between the two reservoirs is 12m, what is the required pipe size

  Calculate strains for case where coordinate axes are rotated

An element of material subjected to a plane strain has a strain epsilon x of 280x10^-6, a strain epsilon y of 420x10^-6 and an engineering shear strain gamma xy of 150x10^-6.

  What is velocity in the channel before the hydraulic jump

Water flows uniformly at a depth of y1 = 40 cm in the rectangular troweled concrete channel shown, which is 10 m wide and has a bed slope of So = 0.040 . What is the velocity in the channel before the hydraulic jump

  Explain what is the hydraulic residence time of the river

An industry is illegally discharging benzene into a river. The concentration in the river at the point of discharge is 0.2 mg/L. A drinking water treatment plant (DWTP) is located 1.5 km downstream. The water velocity in the river is 0.35 km/day.

  What is concentration of fe needed to maintain concentration

At a wastewater treatment plant, FeCl3 (s) is added to remove excess phosphate from the effluent. Assume the following reactions occur: FeCl3(s) Fe3+ + 3Cl- Fe3+ + PO4 (3-) FePO4 The equilibrium constant for the second reaction is 10^26.4.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd