What is the maximum flowrate in the business can discharge

Assignment Help Civil Engineering
Reference no: EM13563799

A business wishes to discharge salt into a river. the concentration of salt from the business is 210 mg/L. the flow of water in the river (upstream) is 0.5 m^3/s. Upstram the concentration of salt in the river 15 mg/L. What is the maximum flowrate in (m^3/s) the business can discharge the salt if the concentation of salt in the river (after mixing) cannot exceed 75 mg/L. Include a diagram depiciting the problem. The system is complete mix. Assume that the mixed flowrate is same

Reference no: EM13563799

Questions Cloud

Estimate the value of the fuel that is captured if the vapor : Gasoline vapors are vented to the atmosphere when an underground gasoline storage tank is filled. If the tanker truck discharges into the top of the tank with no vapor control
Compute and tabulate the azimuths from the following 3-sided : Compute and tabulate the azimuths from the following 3-sided traverse where course ab is due north. angles are to the right. include a sketch.
Determine the work done and the heat transfer : Water, initially dry saturated vapour at 4 bar, lls a closed rigid con- tainer. The water is heated until its temperature is 400C. Determine the work done and the heat transfer.
What is the concentration of nox : It has been estimated that the emission of NOx from a coal fired power plant is 1300 g/s. At 100 km downwind (y=10m), what is the concentration of NOx in g/m^3. The wind speed at the top of the stack with a height of 100m is 6.5 m/s and an inversion ..
What is the maximum flowrate in the business can discharge : A business wishes to discharge salt into a river. the concentration of salt from the business is 210 mg/L. the flow of water in the river (upstream) is 0.5 m^3/s. Upstram the concentration of salt in the river 15 mg/L.
What is the theoretical rate of moisture removal : Moisture in the hot drying air condensing on the cooler grain near the plenum of the bin (Hint: The vapor in the ambient will condense out if the temperature of a surface is lower than the incoming air dew-point temperature).
Determine the station of the point where the superelevation : A 6 lane highway has 12 ft lanes and a crown cross-slope of 0.02 ft/ft. The design speed of the road is 60 mph. The station of the PC is 20+00. Determine the station of the point where th superelevation runoff begins
Find the minimum number of coins he has : According to his will: First give one coin to manager. 1/5th of the remaining to the elder son. Now give one coin to the manager and 1/5th of the remaining to second son and so on..... After giving coins to 5th son, divided the remaining coins among ..
What is the reason for the relatively high strength of wood : The de-carburization of a steel can also be described by the error fuction. Starting with the equation, (cx-c0)/(sc-c0) = 1-erf(x/(2*(sqrt(Dt)))), and taking cs=0 derive an expression to describe the concentration profile of carbon as it diffuses out..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What amount must jackie invest over the next

Jackie is now exactly 40 years old, and plans to invest a recurring amount over the next 15 years (until age 55) in an account bearing 10% annual interest. She plans to retire at age 65 and live to age 100

  Determine the maximum compression of the spring

The 30-Mg freight car A and 15-Mg freight car B are moving toward each other with the velocities VA= 20 km/h to the right and VB= 10 km/h to the left. the spring constant on car A is k= 3MN/m.

  Determine what is the rate of flow into the reservoir

Runoff from a storm flows into a reservoir with a surface area of 20.0 ha at a constant rate. The reservoir level is observed to rise at 1 mm per minute when water is being released through the dam at a rate of 10 m3 per second.

  Determine what is the quality of mixture of liquid and vapor

if the mass of liquid to vapor in a mixture of saturated liquid and vapor water is 0.8, what is the quality of the mixture

  Find the temperature stress produced

A rod of steel is 20 m long at a temperature of 200C. find the free expansion of the rod when the temperature is raised to 650C. Find the temperature stress produced

  Determine the factor of safety for the joint at the theta

two wooden members of uniform rectangular cross section of sides a = 100 mm and b = 60 mm are joined by a simple glued joint as shown. knowing that the ultimate stress of the joint are 1.26 MPa in tension and 1.50 MPA in shear and that P= 6kN

  Find the standard deviation of the clearance

It is possible to adjust the mean hole diameter. To what value should it be adjusted so as to maximize the probability that the clearance will be between 0.05 and 0.09 cm?

  Calculate the amount of changes in length of the rod

If the resistivity of this alloy is dependent only on thermal and impurity considerations, find the amount of changes in length of the rod (in mm) when the temperature is changed from T1 to 1.47268x10^2 °C.

  Draw a queue diagram representing the traffic flow starting

an incident occurs on a freeway that has a capacity in the northbound direction, before the incident, of 4000 veh/h and a constant flow of 2900 veh/h during the morning commute.

  Design a rectangular channel contraction from width b1

Design a rectangular channel contraction from width b1 (upstream) to width b2 (downstream). Assume uniform flow approaches the contraction (i.e. normal depth approaching the channel contraction).

  Calculate the min velocity of flow in ft per sec of water

Calculate the minimum velocity of flow in ft/sec and m/sec of water at 160 degrees F in a 2 in. dia pipe for which the flow is turbulent

  What is the freshwater head in the piezometer in the water

A piezometer in a water-table aquifer is screened just above a leaky confining layer and a piezometer in a semi-confined aquifer is screened just below the leaking confining layer. The water level in the water-table aquifer is 1.42 m below the ground..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd