What is the maximum exiting velocity and what is the maximum

Assignment Help Civil Engineering
Reference no: EM13561636

1.A fireman reduces the exit area on a nozzle so that the velocity inside the hose is quite small relative to the exiting velocity. What is the maximum exiting velocity and what is the maximum height the water can reach if the pressure inside the hose is 200 psi?

2.The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL. TCE is added to the aqueous phase so that initally it has an aqueous phase concentration of 100 ppb. After the system equilibrates, what will be the concentration of TCE in the aqueous phase?

Reference no: EM13561636

Questions Cloud

Find the uniform annual amount that is equivalent : Find the uniform annual amount that is equivalent to a uniform gradient series in which the first year’s payment is $500, the second year’s payment is $600, the third year’s payment is $7000, and so on, and there is a total of 20 payments.
What is the maximum exiting velocity and what is the maximum : A fireman reduces the exit area on a nozzle so that the velocity inside the hose is quite small relative to the exiting velocity. What is the maximum exiting velocity and what is the maximum height the water can reach if the pressure inside the hose ..
Determine the moment of all cable forces about point a : Structure O A B C is built in at point O and supports forces from two cables. Cable E A D passes through a frictionless ring at point A, and cable O C G passes through a frictionless ring at point C. If the force in cable E A D is 800 lb and the forc..
Determine head loss through this pipe section : A pipe carrying oil of specific gravity (SG = 0.877) changes in size from 150 mm at section E to 450 mm at section R (E and R are arbitrary designations of the two points in the system).  Section E is 3.66 m lower than R
Take the casing wall to have an outer diameter : Batteries in a flashlight must be held in electrical contact even though the outer plastic housing expands differently than the battery and terminals. This is accomplished by having a compliant spring compressed as the cover is screwed on the flashli..
What will be the steady-state effluent concentration : A water treatment plant treats a continuous flow rate of 50,000 m^3/day and plans to build a 10,000 m^3 tank to house an additional treatment process. The reaction occurring in the tank will remove nitrate according to first order decay with a rate o..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What speed will the sleeve attain

A Newtonian fluid is in the clearance between a shaft and a concentric sleeve. When a force of 600 N is applied to the sleeve parallel to the shaft, the sleeve attains a speed of 1 m/s. If a 1500 N force is applied

  Calculating the force in a punch press

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa.

  Plot transition from tangent to full superelevated section

The superelevation rate is 0.084. Prepare a plot showing the ordinates required for the transition from the tangent section to the full superelevated section, assuming that the pavement width is 7.3 m wide. Make any necessary assumptions.

  What is the concentration of mlvss in the activated sludge

The concentration of Chemical Oxygen Demand (COD) in the effluent from this system is 25 mg L-1. The growth rate of the organisms in this case is 0.9 days-1. The activated sludge tank has a volume of 50 m3 and the flow rate through it is 500 m3 da..

  Determine the overturning moment of silt and water

Assuming that silt is equivalent to a liquid having a density of 1760 kg/m3, determine the overturning moment of silt and water about point A.

  Find what is the range of the values that would be expected

a spot speed study was conducted on a freeway on which the mean speed and the standard deviation were found to be 72 .4 mi/hr and 5.4 mi/hr, respectively. what is the range of the values that would be expected to contain the middle 95 percent of s..

  To what phmust the water be raised and maintained

A water contains contains 2.0 meq/LCa2+ and 1.3 meg/L Mg2+. If one wanted to remove the hardness species by hydroxide precipitation, to what pHmust the water be raised and maintained in order for both calcium and magnesium toform hydroxide solids?

  Determine max magnitude of pq that satisfies limit states

The beam is fully restrained at both ends but is unbraced along its span. Determine the maximum magnitude of PQ that satisfies the ultimate strength limit state for flexural strength

  What is the probability that the vehicle pulling out

what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?

  Determine the hydraulic conductivity of the aquifer

Drawdown at a 0.20 m diameter, fully penetrating well, which has been pumping at the rate of 1000 m^3/day for a long enough time that steady state conditions have been reached, is determined to be 0.70 m.

  Determine temperature when thermal equilibrium is reached

A 50-kg iron block at 80C os dropped into an insulated tank that contains 0.5m^3 of liquid water at 25C. determine the temperature when thermal equilibrium is reached.

  Compute the volume of the water squeezed out of the clay

A 10,000 ft3 mass of saturated clay had a void ratio of 0.962 and a specific gravity of solids of 2.71. A fill was then placed over this clay, causing it to compress. However, the volume of the solids remained unchanged.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd