Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.A thin film of oil (v=0.001 m^2/s) 2mmthick flows down to a surface inclined at 30 degrees to thehorizontal. What is the maximum and mean velocity of flow?
2.Whisker filaments of SiC that are 5 μm thick are coated withan aluminum alloy using a chemical bonding process. The coating process is carried out at 650 oC before the sample iscooled to room temperature. Elastic stresses due to thermalexpansion mismatch do not begin to appreciably accumulate until thealloy has cooled to approximately 200 oC due to alloyviscosity. If the stresses necessary to maintain whisker/coatingcompatibility are assumed to be normal stresses acting only in thedirection of the filament axis, what is their sign and magnitude at20 oC? Relevant materials properties are:ESiC = 476 GPA, EAl = 70 GPA,αSiC = 4.7 x 10-6/oC,αAl = 21 x 10-6/oC.Looking a wood (pine) deck material. It's a simple 8' by 8' deck. There's a support beam holding up this deck. Other end is connected to building. I'm trying to find the load bearing strength of a support beam -- in lbs, that supports this deck under it. Average usage of deck or persons on it. Anyways, what is the strength of a single 8 foot 2" by 12" beam? Then what is the strength of a single 8 foot 2" by 10" beam?
3.102 Determine the intensity w of the maximum distributed load that can be supported by the hanger assembly so that an allowable shear stress of τallow = 13.5 ksi is not exceeded in the 0.40-in.-diameter bolts at A and B, and an allowable tensile stress of σallow = 22 ksi is not exceeded in the 0.5-in.-diameter rod AB.
A short hollow cast iron cylinder with a wall of thickness of 1 inch. is to carry a compressive load p=150 kips. compute the required outside diameter if the working stress in compression is 12,000 psi
1-what criteria should zachary use evaluate the project ?2-what assumptions should he make?3-what additional data and
determine the temperature of propane when the pressure in the tank drops to 1 atm. Also determine the total amount of heat transfer from the environment to the tank to vaporize the entire propane in the tank.
A saturated soil has a unit weight of 120 pcf and a water content of 32.5%. Determine the void ratio and specific gravity of the soil.
The 20-lb cart B is supported on rollers of negligible size. If a 10-lb suitcase A is thrown horizontally on it at 10 ft/s, determine the length of time that A slides relative to B, and the final velocity of A and B. The coefficient of kinetic fri..
A hot-rolled 7-mm-diameter steel rod is axially loaded at room Temp under a fully reversed cyclic loading. under the rotating beam test, the endurance limit for this steel is 470 MPA, under static loading the ultimate strenght is 1200 MPA.
A new section of richmod highway is being designed as a six-lane facility (three in each direction) with a two-way, left-turn lane. Determine the peak hour LOS. Assumed base free flow speed = 55mi/h
A solid steel bar of diameter 30 mm is enclosed by a steel tube of outer diameter 45 mm and inner diameter 36 mm. Both bar and tube are held rigidly at end A and joined securely to a rigid plate at end B. The composite bar, which is 500 mm long, is t..
A small city is evaluating disinfection requirements for their drinking water plant. With an average flow of 5 MGD and a peak flow of 9 MGD, determine the controlling CT factor (virus or giardia) when the water temperature is 23 degrees C.
The total saturated thickness of the aquifer is 15 m. Predict the concentration distribution along the water table after 5110 days, assuming a linear groundwater velocity of 1.6x10-3; dispersivities in x, y, and z of 5.0 m, 0.5 m, and 0.1 m
For this problem you will write a function that calculates avalue between zero and one for each element in a 512x512 matrix(yes thats 512x512).
The dissolved oxygen of sample water is 1.5 mg/L. At 25 C, the dissolved oxygen of the dilution water is 8.25 mg/L. You are told the BOD5 of the sample is 130 mg/L. You have a target final dissolved oxygen of 3.0 mg/L (give yourself some leeway).
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd