Convert the bearings to azimuths from north

Assignment Help Civil Engineering
Reference no: EM13533352

Q 1 convert the bearings to azimuths from north and compute theangle . smaller then 180 degree. between successive bearings.

N66 degree 17' 36"E, S44 dgree 22'34"E, S8 degree 23' 42"W,and N57 degree 08' 55"W.

Q2 compute theazimuth from north of lin CD . ( Azimuths of AB arealso from north.)

Bearing AB= S59 degree 48' 23"W; angle to the right

ABC = 205 degree 56' 11" , BCD= 195 degree 23' 08".

Reference no: EM13533352

Questions Cloud

What is the maximum and mean velocity of flow : A thin film of oil (v=0.001 m^2/s) 2mmthick flows down to a surface inclined at 30 degrees to thehorizontal. What is the maximum and mean velocity of flow?
Write a short class that shows an increment and decrement : A beam of length 3m with a non-uniform load of zero at end Aand 200N/m at end B i.e a vertical loading of 1/2 *200*3N with abending moment about A of 1/2*200*3*(2/3*3). The beam is supportedat end A for a distance of 0.5 m and a uniform suport force ..
You are designing a highway bridge : You are designing a highway bridge. In particular you aretrying to determine how to put the road surface on the bridge. Youlive in an area where the maximum summertime temperature is 40 degrees centigrade and the minimum winter temperature is -30degr..
What would be her recoil velocity : In a football game, a receiver is standing still, having just caught a pass. Before he can move, a tackler, running at a velocity of +3.1 m/s, grabs him. The tackler holds onto the receiver, and the two move off together with a velocity of +1.6 m/s
Convert the bearings to azimuths from north : Convert the bearings to azimuths from north and compute theangle . smaller then 180 degree. between successive bearings.
How much energy in horsepower islost by the water while flow : A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.
Determine the volume of traffic across the bridge : A bridge has been constructed between the mainland and anisland. The total cost (excluding toll) to travel across thebridge is expressed as C=50+0.5V, where V is the number of veh/dayand C is the cost/vehicle in cents. The demand for travelacross the..
What is the average chear stress in the glue joint between : Two 1/2 inch rods are spliced together by glueing a 2 inch section of plastic pipe over the rods ends. If a tensile force P = 350 lb is applied to the spliced nylon rod, what is the average chear stress in the glue joint between pipe and the rods?
Calculate expected error l if a theodolite has direct : The bottom of a rectangular flume is 5mabove reference level. The depth of the water in the flume is 3m.The average velocity is 1.7 m/s. Compute the total hydraulic energyat the surface of the water and at the bottom of the flume.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what diameter pipe would be recommend

A circular concrete pipe (n = 0.012) carries a discharge of 450 cfs with a slope of 0.008 and is designed to run no more than 60% full (by depth). What diameter pipe would you recommend

  Determine the basin dimensions

Determine the basin dimensions (width, length, depth) for a detention time of 3 hours and a length to width ratio of 4 to 1. (use English units)

  Determine the moment of the forces around point a

The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. If the tension in the cable is 1125 N (thus 1125 N in section BG and 1125 N in section BH)

  Determine the hydraulic conductivity of an artesian aquifer

An experiment was conducted to determine the hydraulic conductivity of an artesian aquifer. The piezometric heads at two points 150m apart were found to be 55 m and 48.5 m above a datum.

  Determine the magnitudes of the normal force acting on block

The coefficient of kinetic friction between block A and the inclined plane is mu_k = 0.11 . The angle of the inclined plane is given by theta = 45. Neglect the weight of the rope and pulley. Part A - Normal Force Acting on Block A Determine the ma..

  Prove that the fluid in the pipe will flow from a location

Assume that you have a constant diameter pipe that has no pumps or turbines connected to it.Prove that the fluid in the pipe will flow from a location with high piezometric pressure to one with low piezometric pressure.

  What is the angular velocity of the carriers

If the outer ring rotates in the clockwise direction at 7 rpm and the inner ring rotates in the counterclockwise direction at 12 rpm, what is the angular velocity of the carriers and what is the velocity of C, the center of the top carrier.

  Discuss about damp-proofing trenches

Discuss about damp-proofing trenches

  Show how the gibbs energies of each of the phases vary

On a single graph, show how the Gibbs energies of each of these phases vary with temperature between - 20 C and 150 C for a constant pressure of 80 kPa. You can start your computations at the triple point

  Determinate and indeterminate structures

Doubling the length of a truss member increases its Euler Buckling capacity by a factor of 4

  What flow rate does the filter handle during production

A rapid sand filter has a loading rate of 8.00 m/h, surface dimension of 10m x 8m, an effective filtration rate of 7.70 m/h, and a production efficiency of 96 percent.

  Determine at what point does the new method pay off

Assume that a new method allows her to sort 20 rings/min but costs $500 to implement. Is it worth implementing the new method for a batch of 50,000 rings. At what point does the new method pay off.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd