What is the finished grade elevation on the curve at station

Assignment Help Civil Engineering
Reference no: EM13298715

A sag vertical curve along an existing vertical alignment begins at station 23+45 and ends at station 30+25. The initial grade coming into the curve is -2% and the grade out is +5%. What is the finished grade elevation on the curve at station 27+00 if the PVT elevation is 100.00'?

Reference no: EM13298715

Questions Cloud

What is the probability that the paper has either a 3 or a 6 : suppose there are 10 pieces of paper in a hat. Each piece of paper has a digit 1 through 10 written on it. Each number is written only once. You reach in the hat and select a piece of paper. What is the probability that the paper has either a 3 or..
Explain the effect on the equilibrium position of decreasing : Consider the reaction Br2(g) 2 Br(g), which is endothermic as written. What would be the effect on the equilibrium position of decreasing the temperature
Determine how many combinations of 2 books can be selected : A customer randomly select 2 of 10 books to purchase. How many combinations of 2 books can be selected
How to calculate the value of w work for the system : Automobile airbags contain solid sodium azide, NaN3, that reacts to produce nitrogen gas when heated, thus inflating the bag. 2NaN3(s) ------> 2Na(s) + 3N2(g) Calculate the value of w (work) for the following system if 14.7 g of NaN3 reacts comple..
What is the finished grade elevation on the curve at station : A sag vertical curve along an existing vertical alignment begins at station 23+45 and ends at station 30+25. The initial grade coming into the curve is -2% and the grade out is +5%. What is the finished grade elevation on the curve at station
Compute the dealer expected carry income : The dealer can currently borrow $ 2,000 million through one- week repurchase agreements at an interest rate of 1.20 percent. Compute the dealer's expected carry income in each of the following scenarios. ( Hint: A spreadsheet can be most useful he..
Determine the length of the channel for the n : A trapezoidal channel of bottom width 25ft and side slope 1:2.5 carries a discharge of 450cfs with a normal depth of 3.5 ft. The elevations at the beginning and end of the channel are 685 and 650 ft, respectively.
Explain a buffer is prepared by adding sodium acetate : A buffer is prepared by adding 21.0g of sodium acetate ({\rm CH_3 COONa}) to 520mL of a 0.140M acetic acid ({\rm CH_3 COOH}) solution.
Find the magnetic field strength in the center of the tank : In one such test, 150 turns of wire were wrapped around a 7.0-m-diameter cylindrical shark tank. find the magnetic field strength in the center of the tank

Reviews

Write a Review

Civil Engineering Questions & Answers

  What are the x- and y-coordinates of the resulting center

The section of the plywood in the 3rd quadrant is sawed off and the resulting piece is then glued squarely over the 4th quadrant portion of the plywood with glue of negligible weight.What are the x- and y-coordinates of the resulting center of gra..

  Dimensions of symmetrical trapezoid plate

The plate is submerged in a liquid is a vertical position with the parallel sides horizontal and the shorter parallel side at the top and exactly in the surface of the liquid.

  Position of the race car when acceleration is given

Starting from x = 0 with no initial velocity, the acceleration of a race car is defined by the relation a = 6.8e- 0.00057x , where a and x are expressed in m/s 2 and meters, respectively. Determine the position of the race car when v = 30 m/s.

  Determining transformed moment of inertia

Determine the transformed moment of inertia for the beam using steel as the reference material. Express your answer in in^4 to the nearest 0.1 in^4.

  Determine total stress and pore water pressure of sand

a layer of clay, 5m thick, overlies a deposite of sand, 5m thick, which is underlaid by rock. the water table in the sand is sub-artesian with a level at 2m below fround level. the saturated unit weights of the clay and sand are 21 and 16 KN/m^3 r..

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  What is the ratio of the magnitude of e2 to the magnitude

What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.

  Find length and width of square basin for virus disinfection

Find the length and width of a square basin for virus disinfection of a flow of 6 MGD. You may assume a depth of 5 ft, a C•t product of 10 (mg/L) •min for 1.5-log removal, and a target free chlorine residual of 0.6 mg/L.

  At what rate is the diameter increasing

a spherical balloon inflated sos that the volume is increasing at the rate of cubic meter/min. At what rate is the diameter increasing when the diameter is 12 m?

  Calculate the speed at impact on a large rock

A large rock became visible to a driver at a distance of 175 ft. Assuming a perception-reaction time of 0.8s, an initial speed of 42 mph, a coefficient of friction equal to 0.5, and a level roadway, calculate the speed at impact.

  Determine the forces applied at a and b

Knowing that these forces are equivalent to a force-couple system at C consisting of the force C= (- 8 N)i+ (4 N)k and the couple Mc =(360 N ⋅ m)i, determine the forces applied at A and B when Az = 2 N.

  Bernoulli equation-measure the flow rate through the meter

The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd