What is the discharge temperature of the propylene

Assignment Help Chemical Engineering
Reference no: EM131194333

Propylene is compressed adiabatically from 11.5 bar and 303.15 K (30°C) to 18 bar at the rate of 1 kmol s-1. If the compressor efficiency is 0.8, what is the power requirement of the compressor and what is the discharge temperature of the propylene?

Reference no: EM131194333

Questions Cloud

Outline employer rights and responsibilities : Outline employer rights and responsibilities following an OSHA inspection. - Discuss an employer's options to contest OSHA citations and penalties.
Describe the prevailing culture : How would you describe the prevailing culture in your country to a stranger from another land, in terms of the nine GLOBE project dimensions?" Response ParametersThe initial response to the discussion questions must be about 250 words in length.
Monthly business income : Create a label called "Income" and add your monthly business income in the next cell: $25,000. Add a label called "Rent" and enter the amount in the next cell: -$4,000.
Social responsibility in daily operations : For example, waste management can be seen as just a business practice, but it has a larger impact. Provide examples and discuss ways that can improve administrators' level of social responsibility in their daily operations. Consider real or potent..
What is the discharge temperature of the propylene : what is the power requirement of the compressor and what is the discharge temperature of the propylene?
Characteristics of paul as a church planter : Develop a list of the characteristics of Paul as a church planter, teacher, and theologian you gain from the prison epistles. Summarize your views.
Analyze the effectiveness of contemporary nursing theories : Debate the utility of the knowledge of nursing theories and associated theoretical concepts in the process of assessing patient's needs and implementing appropriate care.
Formation of liquid water and damaging compressor : A young engineer expresses concern that compression could result in the formation of liquid water, damaging the compressor. Is there cause for concern? Suggestion: Refer to the Mollier diagram of Fig. 6.4.
Calculate the breakeven point : Physician and other provider salaries on a direct basis are $340 per procedure, and total operating expenses will add another $160 per procedure. Calculate the breakeven point for this potential new service line.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  What is the temperature at the exit of the pump

Water is pumped at a flow rate of 2.25 kg/min from 1 bar 20 °C to 15 bar. Determine the amount of work and the temperature of water at the exit if the efficiency of the pump is 78%.

  What is the profit function of this firm

Let p be the price of output, and let the factor prices be fixed. If p = 2 how much will the firm produce? If p = 1 how much will the firm produce? What is the profit function of this firm?

  Dew point of a mixture of hydrocarbons

At a pressure of 10 bar, determine the bubble and dew point of a mixture of hydrocarbons, composition, mol%: n-butane 21, n-pentane 48, n-hexane 31. The equilibrium K factors can be estimated using the De Priester charts in Dadyburjor (1978) or fo..

  Determine the motor speed at a line current of 25 a at 250 v

Assuming that the flux corresponding to a current of 25 A is 40% of that corresponding to a current of 100 A, determine the motor speed at a line current of 25 A at 250 V.

  What is the conductivity of the silicon used

If the velocity of the carriers is 2000 m/s, how many free charges (electrons) must be present in the device at all times?

  What is the temperature at the end of the heating

A sealed rigid tank of 1 m3 capacity contains 1.2 kg of water at 1 bar and 99.63 °C. To this tank we add heat until the pressure increases to 3 bar. What is the temperature at the end of the heating?

  Determine the current i through the 10-? resistor

Determine the current I through the 10-Ω resistor of the circuit of Figure P2.2.5 by employing the node-voltage method. Check by mesh analysis.

  Estimate the kilograms required per hour

The following four solvents, with accompanying distribution coefficients in mass-fraction units, are being considered. Water and each solvent (C) can be considered immiscible. For each solvent, estimate the kilograms required per hour if a single ..

  Calculate the required value of ta1 if the film temperature

Calculate the required value of Ta1 if the film temperature falls to 34°C, and the value if it rises to 36°C.

  Salts in the formula equation

What acid and what strong base would react in aqueous solution to produce the following salts in the formula equation? Write the balanced formula equation for each reaction.

  Recommend installation of the orifice meter

Manometers connected across the venturi and the orifice contain a non-miscible liquid (sp gr = 1.56) in contact with the liquid mixture

  Find the power factor and current of the other machine

If one of the machines has its field excitation adjusted such that it delivers 125 A lagging current, determine the armature current, power factor, excitation voltage, and power angle of each machine.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd