What is the deflection at the end of the beam

Assignment Help Civil Engineering
Reference no: EM13561650

A C10x20 catilever beam is 12 feet long, supported on the right side. The beam supports two point loads: Load 1 is 2500 lbf and is located 2.5 feet from the wall. Load 2 is 1300 lbf and is located 12 feet from the wall.

E=29x10^6 psi

I= 78.9 in^4

What is the deflection at the end of the beam (12ft) due to point loads and the beam weight?

What is the deflection at the center of the beam (6 ft) due to the point loads and the beam weight?

Reference no: EM13561650

Questions Cloud

A missile is being shot with an initial velocity : A missile is being shot with an initial velocity of 60m/s at an angle of 60 degrees with respect to the horizontal. Located at a distance of 1000 meters from the missile launch, you are located at a height of 150 meters and try to intercept the missi..
Shoot supplies from ground so that they reach top of plane : You are trying to shoot supplies from the ground so that they reach the top of a plane while flying low. The plane is flying at an altitude of y=20 meters high and with a speed of 30m/s, and you want to project your medical supplies with an initia..
Dipole is perpendicular to the electric field : A dipole of moment 0.7 e · nm is placed in a uniform electric field with a magnitude of 70000 N/C.What is the magnitude of the torque on the dipole when the dipole is perpendicular to the electric field?
Floor is connected to horizontal spring of force constant k : A box of mass m on the floor is connected to a horizontal spring of force constant k. The coefficient of kinetic friction between the box and the floor is µk. The other end of the spring is connected to a wall.
What is the deflection at the end of the beam : A C10x20 catilever beam is 12 feet long, supported on the right side. The beam supports two point loads: Load 1 is 2500 lbf and is located 2.5 feet from the wall. Load 2 is 1300 lbf and is located 12 feet from the wall.
What is the delfection due to self weight at the end of the : A 13 foot long C10x25 beam is supported as a cantilever beam where x=0 on the left end. It is subject to no externally applied loads.
How does the engineering classification of soils differ from : A sample of undisturbed soil has a dry weight of 10 lb and volumen of 1 ft^3. If the specific gravity of the soil solids is 2.65, determine the void ratio and the porosity.
What is the crest length of the model in feet : The length of time the model must be operated to check the equivalent of 36 hours of operation for the prototype operation, in decimal format hours.
What is the braking efficiency : A car is traveling up a 3% grade on a road that has good, wet pavement. The engine is running at 2500 rpm. The radius of the wheels is 15 inches, the driveline slipage is 3% and the overall gear reduction ratio is 2.5 to 1

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute andcompare its theoretical density

Molybdenum has a BCC crystal structure, an atomic radius of0.1363 nm, and an atomic weight of 95.94 g/mol. Compute andcompare its theoretical density with the experimental valuefound inside the cover.( experimental density is 10.22g/cm^3)

  Determine max force the hand can apply without fracturing

The force exerted on the hand causes torsion of the humerus. Let us assume the cross-section of this wrestler's humerus is approximated as hollow (the marrow has little structural strength) with an outer diameter of 19.0 mm and an inner diameter o..

  Calculate the time of flight of the bolt

Calculate the time of flight of the bolt from the ceiling tothe floor. Assume that the elevator continues its upward acceleration. (Use a frame reference fixed with respect to the elevatorshaft)

  Describe how the following ratios and indices are used

A breif explination on clay mineralogy including isomorphous substitution, specific surface, cation exchange capacity and their effect on clay properties.

  Compare and contrast the purpose and scope

Compare and contrast the purpose and scope of the Federal Insecticide, Fungicide, and Rodenticide Act with the provisions of the Federal Food, Drug, and Cosmetic Act.

  Define materials to construct an industrial building

Materials To Construct An Industrial Building, A small building can be constructed of steel or wood framing. A decision is made to use steel for fire resistance.

  Compare the crystalline state in metals and polymers

(a) Compare the crystalline state in metals and polymers. (b) Compare the noncrystalline state as it applies to polymers and ceramic glasses

  What must the ph be raised to in order to precipitate

Groundwater in Taupe, Arizona, initially contains 1.8 mg/L of iron(III). What must the pH be raised to in order to precipitate 0.3 mg/L of the iron (T=25°C)

  Determine the uniform depth in the channel

A clean-earth channel, for which n=0.020, is 6m wide and lies on a slope of 0.005236. Water flows at 30m3/s through the channel and enters a reservoir. The water depth in the channel, just before the entry to reservoir, is 3m.

  What is the linear speed of the wire/bucket in fps

A 10 HP Motor turning 1800 rpm is attached to a 60:1 speed reducing gearbox. The motor has an efficiency of 80%. It operates at 240V AC. A 12" diameter drum is attached to the gearbox output shaft, and a wire rope is wrapped around the drum to act as..

  Consider a cantilever mass-less beam subjected to a

consider a cantilever mass-less beam subjected to a concentrated mass at the tip of the beam.nbspassume length l

  What was the hourly rate of temperature change

If the graphs of the functions f(x) and g(x) intersect at the point (–5, –6), then {–5} is the solution to the equation f(x) = g(x).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd