What is necessary heat transfer per unit mass in kj per kg

Assignment Help Civil Engineering
Reference no: EM13306057

Air (m=28.97kg/kmol) is uniformly heated at steady state as it flows through a cylindrical constant area duct. It enters the channel uniformly at 2.5atm, 300K and 80m/s and exits at 1.5atm. What is the necessary heat transfer per unit mass in kJ/kg to achieve the exit conditions under the following flows? (You can assume that the air behaves as ideal gas at constant x=1.4.)
a) Air exits uniformly at 300m/s.
b) Air flow is laminar with a maximum speed of 300m/s at the exit.
c) Air flow is turbulent (n=7) with a maximum speed of 150m/s at the exit.

Reference no: EM13306057

Questions Cloud

Provide an explanation of hashtables : In your comparison, be sure to include an explanation of one way hashtables are similar to your selected data structure and one way in which they are different.
Strategy & policy& competitive positioning & relative cost : Strategy & Policy (Furman) & Competitive Positioning & Relative Cost Analysis
Estimate the mass of the water : A cup of water is heated with a heating coil that delivers 14.87W of heat. What is the mass of the water
Determine the number of revolutions exected by gear a : A load is to be raised 20 ft by the hoisting system. Assuming Gear A is initially at rest, accelerates uniformly to a speed of 120 rpm , determine (a) the number of revolutions exected by gear A in raising the load. (b) The time required to raise ..
What is necessary heat transfer per unit mass in kj per kg : Air (m=28.97kg/kmol) is uniformly heated at steady state as it flows through a cylindrical constant area duct. It enters the channel uniformly at 2.5atm, 300K and 80m/s and exits at 1.5atm.
What is the engines thermal efficiency in percent : A heat engine does 798.57 J of work per cycle while exhausting 163.83 J of waste heat. What is the engine's thermal efficiency in percent
What is the maximum torque on the motor : A motor run by a 7.6V battery has a 15 turn square coil with sides of length 3.0cm and total resistance 25ohms. What is the maximum torque on the motor
Provide a diagram showing the cost of the truss as function : A project for constructing a Facility just started. It involves the excavation of 40 to 60 feet deep and 60 feet wide trench to house double tunnels. A 24-inch outside diameter (22.5-inch inside diamater) water line is located in the path of the t..
Determine how far is the cannon from the observer : A cannon fires a cannon ball at 769.26 m/s in a straight line that passes directly over an observer's head. how far is the cannon from the observer

Reviews

Write a Review

Civil Engineering Questions & Answers

  Maximum volume of treated wastewater

Roughly what is the maximum Volume of treated wastewater should you put in the bottle if you want to have at least 2.0mg/l of DO at the test (filling the rest of the bottle with the water

  How much more flow in cfs will be attained with project

If a 96-inch brick sewer (n = 0.015) is laid on a slope of 0.01% is set to be rehabilitated with GIPL (n = 0.01) that will need 2-inches all around it. How much more flow, in cfs will be attained with this project

  Determine the magnitudes of the velocity of point o

The two pulleys are riveted together to form a single rigid unit, and each of the two cables is securely wrapped around its respective pulley. If point A on the hoisting cable has a velocity v=0.9 m/s,

  What were the magnitude and the direction of the velecity

If friction between the cars and the rails is neglected, what were the magnitude and the direction of the velecity of the cars after the collision?

  Determine the factors of safety against sliding

assume hydrostatic uplift varies uniformly from full hydrostatic head at the heel of the dam to zero at the toe. consider 1m length of dam.

  Explain how to plot the hydraulic grade line

Water is pumped from a reservoir whose surface elevation is 1390 ft to a second reservoir whose surface elevation is 1475 ft. The connecting pipeline is 4500 ft long and 12 in. in diameter.

  Find angular acceleration needed to keep prisoner in beam

Find the angular velocity and angular acceleration needed to keep the prisoner in the beam of the spot light at the moment when the prisoner is 4000 ft away from the spot light.

  Writing case study about bridge collapse

Writing case study about bridge collapse

  Estimate the hydraulic retention time if the reactor is pfr

A biological reactor is used to treat wastewater from a small community (Q = 100,000 gpd). The influent BOD5 concentration to the reactor is 200 mg/L and the required effluent BOD5 concentration is 30 mg/L.

  How much dividend income will receive over the next year

A corporation issues a new 10 year bond that has a coupon rate of 4.65% with quarterly dividend payments. Alex purchases 200 of these bonds at a price of $98.75, for a total investment of $19,750. Assuming he holds them to maturity, what will be..

  Estimate the particle removal efficiency

How do you propose to do this at the above treatment plant and estimate the head loss both immediately after backwash and 10 hours later, if the same water is applied at a rate of 2 L/s.m 2 .

  Find what depth of aggregate is needed at the angle theta

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd