Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An ogee spillway of a gravity dam is to be modeled using water. The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10, calculate the height of the model.
Calculate the head of the crest of the model for the maximum discharge, in inches.
What is the crest length of the model, in feet
What is the capacity of the pump required to supply maximum required discharge to the model, in CFS The length of time the model must be operated to check the equivalent of 36 hours of operation for the prototype operation, in decimal format hours.
Assuming an isotropic and homogenous hydraulic conductivity of 0.0001 cm/s what is the magnitude and direction of specific discharge (q)?
Field tests have shown that the Horton equation best describes the composite roughness of the channel. Find the capacity of the main channel and the lateral extent of the floodplains for a 100-year flow of 1590m^3/s.
A block of material A is placed in closed contact with unlimited supply of material B, after 15 hours at temperature T1, it is observed that atoms of B have penetrated 0.5mm into material A.
The center 0 of the wheel is mounted on the sliding block, which has an acceleration of a0= 8 m/s2 to the right. At the instant when theta=45 degrees, theta dot is = 3 rad/s and theta double dot is = -8 rad/s2.
An element of aluminium in a form of a rectangular parallel pipe has a length 'a' along the x axis of 5.5 in, a length 'b' on the y axis of 4.5 in. Determine the maximum shear stress in the material,the change in length.
Determine the axial and hoop stresses at the lower end of the vessel. A standpipe 12 ft in diameter and 50 ft tall is being con- structed for use as a storage tank for water with a specific weight of 62.4 lb/ft3. The wall thickness of the vessel is..
The owners wish to achieve an initial acceleration from rest of 22 ft/(sec^2) on a level paved surface. What is the minimum coefficient of road adhesion needed to achieve this acceleration
the maximum degree of curvature can be at most 6.0 and the superelevation can be at most +6.0%. Design the ramp for the highest horizontal curve design speed given the constraints.
A circular concrete pipe (n = 0.012) carries a discharge of 450 cfs with a slope of 0.008 and is designed to run no more than 60% full (by depth). What diameter pipe would you recommend
Due to temperature change, a 1/32" hole mismatching occurred. What is the pulling force, in lbs, to be applied for one of the plates to match the two holes The plate length is 3 ft (from the left end to the hole) and its cross section is 1/8" x 1"..
A 1.0 × 106 gallon reactor is used in a sewage-treatment plant. The influent biochemical oxygen demand (BOD) concentration is 100 mg/L, the effluent BOD concentration is 25 mg/L, and the flow rate through the reactor is 500 gal/min.
The depth to water in A is 210 ft, in B is300 ft, and C is 230 ft. Determine the direction of ground water flow through the triangle ABC and calculate the hydraulic gradient. If the aquifer hydraulic conductivity is 30 ft/day, estimate how far gro..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd