What force is necessary to lift a thin 25-mm diameter ring

Assignment Help Civil Engineering
Reference no: EM13529919

What force is necessary to lift a thin 25-mm diameter ring out of :

a) water, and

b) ethyl alcohol.

Neglect the weight of the ring and assume a temperature of20oC.

Note: Please show allsteps, and include any necessary explanations

Reference no: EM13529919

Questions Cloud

Calculate the final pressure temperature when the nitrogen : Calculate the final pressure, temperature when the nitrogen isreduced to that volume. What is the modulus of elssticity at thebeginning and end of the compression. k=1.4
The magnitude of the unit vector of bxa : For Vectors A=(i + 2j - 3k) and B=(4i - 5j + 6k), determine:
What are the force and total time required : What is the weight of a 10-ft3 tank of oxygen if the oxygen is pressurized to 400 psia, the tank itself weighs 100 lbf, and thetemperature is 700F?
What is the modulus of elasticity at the beginning and end : One cubic meter of nitrogen at40oC and 340 kPa iscompressed isoentropically to 0.2 m3. Calculate the finalpressure and temperature when the nitrogen is reduced to that volume.
What force is necessary to lift a thin 25-mm diameter ring : What force is necessary to lift a thin 25-mm diameter ring out of :
What net force does that put the door of size 2 m by 1m : Water at 120 celcius with a quality of 25  % has its temperature raised 20 celcius in a constant volume process.  What is the new quality and pressure?  Draw P-v and T-s diagrams.
Calculate the length of the rough patch : On an essentially frictionless ice rink, a skater moves at 3 m/s. Find the length of the rough patch
What is the resulting data rate : You digitize a 10-kHz signal by sampling it at twice the highest frequency (i.e 20,000 times a second) and encoding the the intensity in 8-bits. What is the resulting data rate
Determine how many turns of wire are needed : The resistance of a very fine aluminum wire with a 20.0um* 20.0um square cross section is 1000 ohms. How many turns of wire are needed

Reviews

Write a Review

Civil Engineering Questions & Answers

  Maximum total load that can be applied to a truss

How do you find the force ratio equation to determine the maximum total load that can be applied to a truss? Given a force of a member how do you find the force ratio?

  Could apparatus be used for determing the density of liquid

The u-tube manometer has legs of unequal internal diameter d1 and d2, which are partially filled with immiscible liquids of density1, and density2 respectively and which are open to the atmosphere at the top.

  Hydraulic radius of the river

In that season, what are the hydraulic radius of the river, its mean velocity and volumetric discharge?

  Compute the cars stopping distance and time

at s=0 the driver applies the brakes hard enough to cause the car to skid. Assume that the car keeps sliding until it stops, and assume that throughout this process acceleration is a= -7.4556. compute the car's stopping distance and time.

  Calculate the temperature of flat world that has an albedo

Calculate the temperature of "flat world" that has an albedo of 0.31 and a solar flux of 1370 w/m^2. One side of flat world faces the sun. Ignore energy emitted from the edge of flat world.

  Qualitative or quantitative risk assessment on the project

Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?

  Calculate the vertical displacement of joint b

Ignoring both axial and shear deformations and using the unit force method, calculate the vertical displacement of joint B.

  The length of line measure with a tape having a nominal

The length of line measure with a tape having a nominal length of 1ch is found foud to be 20.03 ch. if the tape is 0.3 link too long  the true lenght  of the line is  wich one is correct is A 26.04ch or B20.09ch or  C19.97ch or D 14.02 ch wich one is..

  Determine the maximum design shear force for the loading

A simply supported span of 28 feet must carry a uniform loading that produces a total factored maximum moment of 300 K-ft including the beam weight. The concrete can be 3.5 ksi and the steel is grade 60.

  What would be the horizontal and vertical component from

what would be the horizontal and vertical component from this acting force see diagram

  Determine max shearing stress and coexisting normal stress

A 40 mm diameter solid brass shaft in a marine vessel is subjected to a simultaneous torsion of T=250 N.m and axial thrust of P=25kN. Show the combined state of stress on the surface element of the shaft.

  After falling from rest from a height of 32 m a 045 kg ball

after falling from rest from a height of 32 m a 0.45 kg ball rebounds upward reaching a height of 22 m. if the contact

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd