What flow rate of fresh water (in m3/s) must they use to red

Assignment Help Civil Engineering
Reference no: EM13560403

A bankrupt chemical firm has been taken over by new management. On the property they found a 20,000 m3 brine pond containing 25,000 mg/L of salt. The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean, which has a salt concentration above 30,000 mg/L. What flow rate of fresh water (in m3/s) must they use to reduce the salt concentration in the pond to 500 mg/L within one year?

Reference no: EM13560403

Questions Cloud

Calculate the critical radius and the number of atoms : Calculate the critical radius and the number of atoms in the nucleus of the homogeneous nucleation in GERMANIUM. The latent heat of fusion is 8100 cal per g-mile (atom) and the coefficient of linear expansion is 5.75*10^-6 per K
Basic case analysis assignment : Basic Case Analysis Assignment
Determine the hydraulic conductivity of the soil sample : A constant head permeameter has a sediment sample with a cross sectional area of 100 cm^2. The sediment sample is 30 cm long. The porous plates on top and bottom of the sample holding it in place have a vertical hydraulic conductivity of 0.001 cm/s a..
Medical devices sold in japan : Medical devices sold in Japan
What flow rate of fresh water (in m3/s) must they use to red : mg/L of salt. The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean, which has a salt concentration above 30,000 mg/L.
Why quantitative risk is so important in risk mitigation : Why quantitative risk is so important in risk mitigation
What is your best estimate of the true value of the angle : What is your best estimate of the true value of the angle? Give your answer to 1 decimal place of a second.
Find the change in enthalpy : Oxygen flows without a gain or loss of heat through a horizontal pipe of constant cross section. At section 1 the pressure 175 psia, the velocity is 78 fps, and the temperature is 50°F; at section 2 the pressure is 130 psia, the velocity is 95 fps, a..
Global marketing management : Global marketing management leadership creates the strategic synergy capable of synthesizing strategic plans into purposeful action. Leadership instills global marketing control in three major governance modes: functional (e.g., global marketing mix)..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the final temperature of the water

A piston-cylinder device contains 0.2kg of water initially at 800 kPa and 0.06m^3. Now 200 kJ of heat is transferred to the water while its pressure is held constant. Determine the final temperature of the water.

  What should the reading be at y to adjust collimation error

a level is setup midway between X and Y reads 5.572 ft on X and 4.946 ft. on Y. The level is setup very close to X and a reading of 4.666 ft. is taken on X. what should the reading be at Y to adjust any collimation error of the level

  Determine void ratio and dry unit weight of compacted sample

A soil sample is prepared in the laboratory by mixing a certain amount of dry soil with 10.5 wt% water. The relative density of the grains of the material is equal to 2.7.

  Determine the velocity of the steam at the nozzle outlet

Helium enters an adiabatic steady-state nozzle at 200kPa and 124 degrees Celsius and 10m/s. At the nozzle exit the temperature of the helium is 100 degrees Celsius and the pressure = 150 kPa.

  1 you are working for urs on a building project in dearborn

1. you are working for urs on a building project in dearborn michigan. you are responsible for the design of the

  Calculate what real rate of return will the investor receive

A man bought a 5% tax-free municipal bond .It cost $1000 and will pay $50 interest each year for 20 years.At maturity the bond returns the original $1000 .If there is 2% annual inflation

  Determine the stress in the wall at two points a and b

The end caps are spherical. The cylinder has length of 30 inc., a diameter of 8 in., and a wall thickness of 0.125 in. Determine the stress in the wall at two points A and B. For each, draw the stresses on a 3-D element. Treat the upper cap as spheri..

  What is the rolling resistance

He is concerned about the high rolling resistance of the units in the sand (RR factor 250lb/ton).  What is the rolling resistance?

  What pressure difference would expected for discharge meter

A discharge meter to be used in a 40 cm pipeline carrying oil (kinematic viscosity = 10-5 m2/s, density = 860 kg/m3) is to be calibrated by means of a model (1/4 scale) carrying water (T = 20°C and standard atmospheric pressure).

  How to formulate a linear programming optimization model

A construction company requires to know how much of additives A and B to use to prepare concrete to be used in a freezing environment (northern location). The concrete mix should contain a minimum concentration of nitrate and sulphate.

  Draw shear and moment diagrams for each member of frame

Structural Analysis 8th edition 4-40 draw the shear and moment diagrams for each member of the frame. Assume A is a rocker, and D is pinned.

  The 70 m tall tower is supported by three cables that exert

the 70 m tall tower is supported by three cables that exert forces fab fac and fad on it. the magnitude of the force

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd