What are the internal forces and moment at point a

Assignment Help Civil Engineering
Reference no: EM13298910

Consider the two loading scenarios on the beam, where the beam is supported by a pin joint on the left and roller joint at the right end. What are the internal forces and moment at point A for each scenario?

Reference no: EM13298910

Questions Cloud

Compute data needed to stake the curve at 50 foot increments : Two Tangents intersect at a PI Station of 35+33.24 whose coordinates are N=10349.64 feet and E= 10436.79 feet. The Intersection angle (I) = 20°15'42" Right, and the azimuth of the back Tangent is 23°14'32". (This azimuth is from the PC to the PI.)
Methodologies for software development : ITECH6501 PRINCIPLES OF SOFTWARE ENGINEERING - methodologies for software development in terms of time, cost and resources
Determine moment of inertia of beams cross-sectional area : Determine the moment of inertia of the beam's cross-sectional area about the x-axis. Set a = 40mm , b = 130mm , d = 110mm , h = 380mm .
Determine slenderness ratio l per r and euler buckling load : An aluminum alloy tube with an outside diameter of 2.9 in. and a wall thickness of 0.32 in. is used as a 19-ft-long column. Assume that E = 8300 ksi and that pinned connections are used at each end of the column.
What are the internal forces and moment at point a : Consider the two loading scenarios on the beam, where the beam is supported by a pin joint on the left and roller joint at the right end. What are the internal forces and moment at point A for each scenario
How many u.s. dollars will you need in one year : Today, you purchase a one year forward contract in Australian dollars. How many U.S. dollars will you need in one year to fulfill you forward contract?
Should the company proceed with the new project : The CCA rate on fixtures and equipment is 30%. The companys tax rate is 40% and its cost of capital is 12%. Should the company proceed with the new project?
Determine the emissions of heat-trapping carbon dioxide : Emissions of heat-trapping carbon dioxide (CO2) reached an all-time high of 31.6 gigatons in 2011, a 3.2% increase over 2010. The International Energy Agency said this further reduces the chance that the world can avoid a dangerous rise
At what level of pretax cost savings would be indifferent : At what level of pretax cost savings would you be indifferent between accepting the project and not accepting it?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Long cantilever beam of elastic modulus

A 45 kg machine is placed at the end of a 1.6 m long cantilever beam of elastic modulus 200 x 109 N/m and cross-sectional moment of inertia 1.6 x 10-5 m4.

  Determine the horsepower of the device

water flows from a lake as is shown in fig. p8.40 at a rate of 4.0 cfs. is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. neglect all minor losses and assume the friction factor is .025

  Determine what is the specific yield of the aquifer material

The area is about 100,000 ha, the ground water pumping about 500 million m3 per year, and the water table drop about 3 m per year. Assuming no replenishment, what is the specific yield of the aquifer material

  Determine what is the probability that the system operates

Consider a system that consists of 4 devices. The probabilities of failure for each of the devices are, respectively: 10%, 25%, 20%, and 30%. (a) If these components were in series, what is the probability that the system operates

  Pore water pressure at failure

A CU triaxial test with σc = 20 psi is performed on a sand and a deviator stress of 80 psi fails the specimen. Previous tests revealed that the effective friction angle for this sand is 35°. Calculate the pore water pressure at failure.

  Describe how the surveyor would go about

State the full name of the section of SOLAS that sets out the minimum standards for the training and competence of crew members and describe how the surveyor would go about checking that a vessel had the necessary number of qualified staff.

  Disposal of excavated material

Discuss and use examples to explain the specific factors that you will need to consider when pricing the following items in the bill of quantities foundation excavation

  Determine the horizontal deflection of joint

The maximum vertical load and horizontal load have been identified and shown in the figure. Under this loading condition, you are asked to determine the horizontal deflection of joint C.

  Find the volume of the material using force equilibrium

Your engineering consulting firm has been asked to determine the specific weight of an unknown material. You decide to use the concept of buoyancy to figure this out. So you weigh the material in both air and water.

  Design a logic circuit

Design a logic circuit that, when enabled with an active-high signal named en, will detect four different ranges of values for a 5-bit input number.

  Sketch and annotate the wedge described above

Sketch and annotate the wedge described above.

  Compute the station and elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd