What are the discharge and the flow velocity when the pipe

Assignment Help Civil Engineering
Reference no: EM13562534

1.A horizontal curve on a single-lane highway has its PC at station 124 + 10 and its PI at station 131+ 40. The curve has a superelevation of 0.04 ft/ft and is designed for 65mph. What is the station of the PT?

2.An 18in. diameter sewer is placed on a grade of 1.5ft/1000ft. What are the discharge and the flow veloctiy when the pipe is full?

Reference no: EM13562534

Questions Cloud

Calculate the angular velocity w of the cylinder : The solid circular disk of uniform thickness is released from rest on the 60-degree incline. Calculate the angular velocity w of the cylinder and the magnitude v of the velocity of its center C after it has moved 10 ft down the incline
Design the continuous slab showing using the aci moment : Design the continuous slab showin using the ACI moment coeficients assuming the service live load of 200 psf is to be supported in addition to the weight of the slabs
Evaluate how far does the book slide : A 1 kg physics book lying on a 20 degree incline isattached to a 500g coffee cup. How far does the book slide
How much work was done in firing the projectile : A 2.0-kg projectile is fired with initial velocity componentsV0x=30 m/s andV0y=40m/s from a pointon the earth's surface. How much work was done in firing the projectile
What are the discharge and the flow velocity when the pipe : A horizontal curve on a single-lane highway has its PC at station 124 + 10 and its PI at station 131+ 40. The curve has a superelevation of 0.04 ft/ft and is designed for 65mph. What is the station of the PT?
Calculate the tangential velocity of the satellite : A satellite, mass of satellite=5850 kg, is in circular orbitof 4.1x10^5m above the surface of a planet, which has a radius of4.15x10^6m. calculate the tangential velocity of the satellite
What is the rate of water to be added to the tank : A hole at the bottom of a fish tank releases water at a rate given by the free jet equation. The hole at the bottom has a .5" diameter. If the water level is desired to be at 2' high and be at steady state, what is the rate of water to be added to th..
Calculate rate of change of water mass in the segment : The segment of river shown has a rectangular cross-section, with width 50 ft. The river bed is at angle ?=100 from horizontal. The average velocity is 2 ft/s at the upstream end (point 1), and 3 ft/s at the downstream end .The vertical depths are as ..
What values of a and b will minimize the variance of s : What values of a and b will minimize the variance of S? The answer to this question will take the from a equals a specific number and b equals a specific number.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Solve a linear program that will suggest a hen managentment

Assume that an egg can be hatched only in the week after it is laid. Otherwise it must be saved and sold for 10 cents. Assume that there are no eggs available for hatching in the first week.

  How to determine the force that must be applied at a

The uniform load has a mass of 450 and is lifted using a uniform 35- strongback beam and four ropes. Determine the Tension in the ropes Determine the force that must be applied at A.

  Determine corrosponding pressure exerted by the brass ring

a brass ring of 120-mm outside diameter is fits exactly inside a steel ring of 120-mm inside diameter when the temperature of both rings is 5 degrees C. knowing that the temperature of the rings is then raised to 55 degrees C

  Find how many ml of water will it take to get 10 pounds

How many mL of water will it take to get 10 pounds of dry aggregate to a moisture content of 5%. 1 kg=2.2 pounds

  Determine the average shearing stress in the bolts

A composite beam is made by attaching the timber and steel portions shown with bolts of 14-mm diameter spaced logitudinally every 200 mm. The modulous of elasticity is 10 GPa for the wood and 180 GPa for the steel

  What will be the discharge through the pipe

A pump having the characteristics given in figure 14.9 ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation

  Determine the elastic and plastic section modulus of i-beam

Determine the elastic and plastic section modulus of the I-beam. The axis runs through the center of the beam on both x and y axis (completely symmetrical). Beam properties: h= 12inches tf= 0.5 inches bf= 6 inches tw= 0.25 inches

  Is the fluid accelerating uphill

A fluid with a specific weight of 100lb/ft^3 and a negligibleviscous effects flows in a pipe. The pipe is inclined at 30degrees. Point (1) is located above point (2) in the pipe.

  Determine the initial weight and final density of the water

A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.

  Calculate the principle of shoring system

how to calculate the principle of shoring system in formwork analysis when the secondly floor upper has been poured ?

  What tension load is needed to return length to the original

a meter long steel plate with a rectangular cross section(10mm x 50mm) is resting on a frictionless surface under the sun. the plate temperature is measures to be at 40C.

  Determine what is the required length of the spiral curve

Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd