Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.A thick steel sheet of area 440cm3 is exposed to air near the ocean. After a one-year period it was found to experience a weight loss of 880g due to corrosion. To what rate of corrosion in mm/yr dose this correspond.
2.A footing 3m X 3m carries a pressure of 500 kN/ m2 at a depth of 1m in a sand substrate. The saturated unit weight of the sand is 20 kN/ m3 and the unit weight above the water table is 18 kN/ m3. The design shear strength parameters are c’ = 0 and ?’ = 40°. Determine the factor of safety with respect to shear failure for the following cases:
IF the water table is 1m below ground level,
A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in the figure. The weight of the gate is negligible, and the hinge at O is frictionless.
A nozzle discharges a stream of water with an initial velocity v0 of 50 ft/s into the end of a horizontal pipe of inside diameter d=5ft. determine the largest distance x that the stream can reach.
A room has a floor area of 500 m^2 and a height of 4 m. THe room is involved in a fire with a constant energy release rate of 1 MW. calculate the time till the smoke layer is 1.5 m from the floor for (a) the case where the leakage areas are at the ..
An aluminum link is subjected to axial tension. The loading is limited by the conditions of not yielding and not elongating excessively. The yield limit is satisfied if the stress remains below 50%of the 325M Payield stress.
Consider the rocket on a test stand . The nose of the rocket is fixed. The rocket is of length L, constant EA and constant m, mass per unit length. To investigate longitudinal dynamics, the rocket is modeled using axial elements of equal length.
Explain how the stregth of the economy as a whole could affect the marginal benefits and the marginal costs associated with a decision to purchase a home.
what should be the minimum radius of curvature p for the track at B so that the passengers do not experience a normal force greater than kmg?neglect the size of the car and passengers.Take k=4
You are assined the task of process design for a fixed-bed carbon adsorber system. You are given the following data: the inlet airstream flows at 5000 acfm (at 95 degrees F and 1 atm) and contains .2% n-pentane by volume
A thin-walled cylindrical tank of radius r is subjected simultaneously to internal pressure p and a compressive force P through rigid end plates. Determine the magnitude of force P to produce pure shear in the cylindrical wall.
At a depth of 4 miles in the ocean the ppressure is 9520 psia. Assume that the specific weight at the surface is 64.0 lb/ft^3 and that the average volume modulus is 320000psi for the pressure range.
The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL.
A bar is under uniform axial loads. AB is 1 foot and has a area of .5 in^2 and BC is 1 foot and has an area of .3 in^2. AB has a 1000lb force putting it under tension and BC has a 500lb force putting it under compression. Find stresses in AB and BC a..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd