User Account

All Pages

The tensional force of the string is in position

Assignment Help Mechanical Engineering
Reference no: EM13712204

The 2 kg ball is releast from rest in position 1 with the string horizontal. The length of the string is L =2m and theta 40 degree

1) The ball's velocity when it is in position 2?

2) The tensional force of the string is in position 2?

3) The resultant force of the ball is in position 2?

Reference no: EM13712204

Questions Cloud

Contained is a gas-tight frictionless piston-cylinder : A mass of 2.2 kg of helium at 381 kPa and -253oC is contained is a gas-tight frictionless piston-cylinder. The gas is expanded to a final pressure of 74 kPa in a poly tropic process where n = 1.667. Compute the work done (output positive) in the proc..
Condensed to a saturated liquid in a piston-cylinder device : Maturated water vapor at 800 kPa is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the amount of heat transferred during this process.
Calculate the diffusion coefficient if the diffusion flux : A sheet of BCC iron 1.7-mm thick was exposed to a carburizing atmosphere on one side and a decarburizing atmosphere on the other side at 725°C. After having reached steady state, the iron was quickly cooled to room temperature. The carbon concentrati..
Calculate the mass-flow rate : The truncated nozzle shown in the figure below is used to monitor the mass-flow rate of air in a pipe. The area of the nozzle is 3 cm2. The total pressure and total temperature measured upstream of the nozzle in the pipe are 300kPa absolute and 20°C.
The tensional force of the string is in position : The 2 kg ball is releast from rest in position 1 with the string horizontal. The length of the string is L =2m and theta 40 degree. The ball's velocity when it is in position 2? The tensional force of the string is in position 2?
What should be the minimum horsepower of the lathe : A 3 in. diameter low strength, stainless steel cylindrical part is to be turned on a lathe at six hundred rpm. With a depth of cut of .3 inches and a feed of .025 in/rev. what should be the minimum horsepower of the lathe?
Quality and the total mass of the refrigerant in the tank : A 5-ft 3 rigid tank contains a saturated mixture of refrigerant-134a at 50 psia. If the saturated liquid occupies 20 percent of the volume, determine the quality and the total mass of the refrigerant in the tank
Determine the magnitude of the bending moment : An 80-mm × 40-mm rectangular beam is made of heat treated AISI 4340. On the tension side of the beam, a transverse crack of length 10 mm is discovered. Determine the magnitude of the bending moment M that will cause brittle fracture.
A solar water heater operating at steady state heats water : A solar water heater operating at steady state heats water from 90 0 F to 120 0 F. The panel is 3600 Btu/hr. Determine 1) the mass flow rate of the water in lb/min and 2) the volume of 120 0 F water after 1 hour in gallons.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Steam at 14 mpa and 350 c enters an adiabatic turbine at a

steam at 1.4 mpa and 350 c enters an adiabatic turbine at a rate of 450 kgh. the turbine has an adiabatic efficiency of

  Superheated steam in a piston-cylinder device

Superheated steam in a piston-cylinder device is initially at 200 °C, 600 kPa. Heat is removed from the system during an isobaric process until half of the mass condenses to saturated liquid

  How to determine the equilibrium concentrations of h2 oh

how to determine the equilibrium concentrations of h2 oh and h2o when water is heated to 1000 3000 5000k. what if the

  The a-36 steel axle is made from tubes ab and cd and a

the a-36 steel axle is made from tubes ab and cd and a solid section bc. it is supported on smooth bearings that allow

  The lowest temperature that has been achieved is about 1

the lowest temperature that has been achieved is about 1 times 10-6 k. to achieve this an additional stage of cooling

  A bending moment of 3 kn-m and a torque of 5 kn-m a safety

a solid circular shaft has a diameter of 60 mm and is subjected to a tensile axial load of 200 kn a bending moment of 3

  Calculate the mass in kg of oxygen that has been released

a 10 m3 oxygen tank is at 15 degree c and 800 kpa. the valve is opened and some oxygen is allowed to escape until the

  Determine the final pressure in the tank

Consider 0.8 grams of air (which may be assumed to be an ideal gas) at 295 K and 1.5 bar trapped in a rigid tank. An electrical heater is operated for 30 seconds. During this time the voltage across the heater is 12 V and 0.6 amps pass through the re..

  Define ideal vapor compression refrigeration cycle

Ideal vapor-compression refrigeration cycle, An ideal vapor-compression refrigeration cycle, with ammonia as the working fluid, has an evaporator temperature of -20c and a condenser pressure of 12 bar

  Consider a supersonic flow of free stream velocity of mach

consider a supersonic flow of free stream velocity of mach 3 is flowing over a diamond-wedge airfoil with half angle

  A uniform rod ab of length 3m and mass 20kg is suspended

a uniform rod ab of length 3m and mass 20kg is suspended with its end b against a vertical wall while its end a is

  Give a proposed design and analysisnbspprincipal features

give a proposed design and analysisnbspprincipal features and working principle of any mechanisms using diagrams to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd