User Account

All Pages

Calculate the diffusion coefficient if the diffusion flux

Assignment Help Mechanical Engineering
Reference no: EM13712206

A sheet of BCC iron 1.7-mm thick was exposed to a carburizing atmosphere on one side and a decarburizing atmosphere on the other side at 725°C. After having reached steady state, the iron was quickly cooled to room temperature. The carbon concentrations at the two surfaces were determined to be 0.014 and 0.0072 wt%. Calculate the diffusion coefficient if the diffusion flux is 3.0 × 10-8 kg/m2-s, given that the densities of carbon and iron are 2.25 and 7.87 g/cm3, respectively.

Reference no: EM13712206

Questions Cloud

Explain change in magnetic properties when steel is heated : Explain the change in magnetic properties when steel is heated. Is this due to allotropic properties?
Gravity is just the ratio of density of a material to water : A fan jumps into a swimming pool in an attempt to drown her sorrows. She is able to float on her back...in a position that is neutrally buoyant...so that she can continue to breathe through her mouth. Believing that 70% of her body is composed of wat..
Contained is a gas-tight frictionless piston-cylinder : A mass of 2.2 kg of helium at 381 kPa and -253oC is contained is a gas-tight frictionless piston-cylinder. The gas is expanded to a final pressure of 74 kPa in a poly tropic process where n = 1.667. Compute the work done (output positive) in the proc..
Condensed to a saturated liquid in a piston-cylinder device : Maturated water vapor at 800 kPa is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the amount of heat transferred during this process.
Calculate the diffusion coefficient if the diffusion flux : A sheet of BCC iron 1.7-mm thick was exposed to a carburizing atmosphere on one side and a decarburizing atmosphere on the other side at 725°C. After having reached steady state, the iron was quickly cooled to room temperature. The carbon concentrati..
Calculate the mass-flow rate : The truncated nozzle shown in the figure below is used to monitor the mass-flow rate of air in a pipe. The area of the nozzle is 3 cm2. The total pressure and total temperature measured upstream of the nozzle in the pipe are 300kPa absolute and 20°C.
The tensional force of the string is in position : The 2 kg ball is releast from rest in position 1 with the string horizontal. The length of the string is L =2m and theta 40 degree. The ball's velocity when it is in position 2? The tensional force of the string is in position 2?
What should be the minimum horsepower of the lathe : A 3 in. diameter low strength, stainless steel cylindrical part is to be turned on a lathe at six hundred rpm. With a depth of cut of .3 inches and a feed of .025 in/rev. what should be the minimum horsepower of the lathe?
Quality and the total mass of the refrigerant in the tank : A 5-ft 3 rigid tank contains a saturated mixture of refrigerant-134a at 50 psia. If the saturated liquid occupies 20 percent of the volume, determine the quality and the total mass of the refrigerant in the tank

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Show that the force required to do this is equal to the

a uniform chain of total mass m and total length l lies in a heap on a table. one end is pulled upwards at constant

  Heat is transferred to the water until the pressure increase

A piston cylinder device contains 8.00 kg of water at an initial pressure of 200 kPa. Initially the piston is at rest on a set of stops and the initial volume is 2.00m3. Heat is transferred to the water until the pressure increases to 1000 kPa when t..

  A shaft of radius r and length l is subjected to a

a shaft of radius r and length l is subjected to a uniformly distributed shear. the shaft is fixed at one end and not

  A refrigerator is to remove heat from the cooled space at a

a refrigerator is to remove heat from the cooled space at a rate of 2300 kjmin to maintain it temperature

  Determine the work and heat transfer involved in the

two kilogram of water initially at 200 degc and 0.4 mpa undergoes an isothermal internally reversible compression

  What is the minimum pressure in psig

For a pump in the basement which must deliver water to a bucket on the floor of the upper mechanical room, what is the minimum pressure in psig you will see at the pump discharge.

  Estimate the cost an oil change 5 quarts of oil and new oil

estimate the cost an oil change 5 quarts of oil and new oil filter for your automobile at a local service station.it

  A 10-ft steel beam is lowered by means of two cables a amp

a 10-ft steel beam is lowered by means of two cables a amp b distant of 9-ft unwinding at the same speed from overhead

  A brass rod is stress free at room temperature

A brass rod is stress free at room temperature (20 Deg. C) It is then heated up, but prevented from lengthening at its ends by external forces. At what temperature does the stress in the rod reach -172 MPa? Assume the modulus of elasticity is 100 GPa..

  Determine the mass of the refrigerant that entered the tank

a 3-ft3 rigid tank initially contains r-134a at 120 psia and 100 percent quality. the tank is connected by a valve to a

  If these components have weights wa 45 000 1b wb 8000 1b

due to an unequal distribution of fuel in the wing tanks the centers of gravity for the airplane fuselage a and wings b

  Determine the electrical power that must be supplied to a

a storage tank consists of a cylindrical section that has a length and inner diameter of l2 m and di1 m respectively

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd