The connection is through the flange

Assignment Help Civil Engineering
Reference no: EM13556999

Select an ST shape to be used as a 20-ft long tension member to resist the following service loads: Dead load=38kips live load=115 kips and snow load= 75 kips. The connection is through the flange with 3/4inch diameter bolts in each line. Use A572 Grade 50 Steel.

a. Use LRFD

B. Use ASD.

Reference no: EM13556999

Questions Cloud

What is the magnitude of the electrons initial acceleration : A 30 feet column is braced at the mid-section to prevent premature failure. If the maximum load is 380 kips, select an appropriate W14 section, if any, to support the loading conditions.
Determine the location on the wheel where the net : A wheel rolls to the right with an angular velocity of 2 rad/s while slowing down at a rate of 3 rad/s^2.. knowing the wheel rolls without sliding and ignoring the effect of gravity
Obtain the angular frequency of the particle : A particle with a mass of 3.50 10-20 kg is oscillating with simple harmonic motion with a period of 3.50 10-5 s and a maximum speed of 1.50 103 m/s. Calculate the angular frequency of the particle
Find the maximum force exerted on the block : An oscillator consists of a block of mass 0.800 kg connected to a spring. When set into oscillation with amplitude 34.0 cm, it is observed to repeat its motion every 1.000 s. Find the maximum force exerted on the block
The connection is through the flange : Select an ST shape to be used as a 20-ft long tension member to resist the following service loads: Dead load=38kips live load=115 kips and snow load= 75 kips. The connection is through the flange with 3/4inch diameter bolts in each line. Use A572 Gr..
Estimate the magnitude of the acceleration of the box : A box mass 5.00 kg moves on a ramp that is inclined at 6.9° above the horizontal. A person is applying a constant force F=70.0 N to the box, What is the magnitude of the acceleration of the box
Compute the value of u with equation and revise the design : Use LRFD and select an American Standard Channel shapefor the following tensile loads. Dead load=54 kips live load= 80 kips and wind load=75 kips. The connection will be with two 9inch long longitudinal welds.
Calculate the average pressure on the other walls : Suppose that a 1.00 cm3 box in the shape of a cube is perfectly evacuated, except for a single particle of mass 1.21 10-3 g. Find the average pressure on the other walls
Compute the magnitude of the load that is necessary : An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 X 10^6 psi. A cylindrical specimen of this alloy 0.5 in in diameter and 10 in long is stressed in

Reviews

Write a Review

Civil Engineering Questions & Answers

  What are the important findings

What are the important findings in Austin Road Co. v. OSHRC and Builders Steel Co. v. Marshall? Your response should be approximately 200 - 300 words and include a reference citation for your response.

  What is the solids concentration of primary clarifier sludge

a 20 mgd wastewater treatment plants primary clarifier influent has 800 mg/l solids. the clarifier removes 18 percent of the solids. the sludge flow rate is 0.070 MGD. (a) what is the solids concentration of primary clarifier sludge

  Determine the horizontal and vertical components of reaction

The winch consists of a drum radius 4 in., which is pin connected at its center C. At its outer rim is a ratchet gear having a mean radius of 6 in. The pawl AB serves as a two-force member (short link) and keeps the drum from rotating.

  Determine the magnitude and direction of the shear stress

Crude oil, with specific gravity SG=0.85 and viscosityμ = 2.15×10−3 lbf sec/ft2, flows steadily down a surfaceinclined θ = 30 degrees below the horizontal in a film ofthickness h=0.125 in. The velocity profile is given by u =ρg/μ(hy − y2/2)sinθ

  Explain can the system be viewed as being a pure substance

A system consists of liquid oxygen in equilibrium with oxygen vapor. How many phases are present The system undergoes a process during which some of the liquid is vaporized.

  What is the centerline uniform water depth in the channel

A 2-ft diameter circular pipe has a Manning's n of 0.013 and a bed slope of 2.0 X 10^-3. What is the uniform flow rate in this pipe if it is completely full (Qf) in ft^3/s

  What is discharge revised discharge pressure of compressure

A compressor installed at a whalf (for loading container ships) is able to provide 6 bar.g pressure into the pressure reciever. The compressor is moved to a site that is 5000 ft above sea level (atmospheric pressure 0.85 bar.a

  Divide the sodium hydroxidecharge into 10 smaller charges

Divide the sodium hydroxidecharge into 10 smaller charges, and add them one at a time, makingsure that each is well mixed and the tank temperature has stoppedincreasing before adding the next charge.

  Find how much power is required to maintain straight flight

A small aircraft with a wing area of 250 ft2 and a weight of 2200 lb has a lift coefficient of 0.4 and a drag coefficient of 0.05. 1) How much power is required to maintain straight and level flight

  Calculate the amplitude f0 of sinusoidal excitation force

calculate the amplitude F0 of the sinusoidal excitation force that is necessary to produce a steady-state vibration with a velocity amplitude of 10 m/s at resonance

  What is the minimum coefficient of road adhesion needed

The owners wish to achieve an initial acceleration from rest of 22 ft/(sec^2) on a level paved surface. What is the minimum coefficient of road adhesion needed to achieve this acceleration

  The most famous geyser in the world old faithful in

the most famous geyser in the world old faithful in yellowstone national park has a mean time between eruptions of 85

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd