Determine the location on the wheel where the net

Assignment Help Civil Engineering
Reference no: EM13557002

A wheel rolls to the right with an angular velocity of 2 rad/s while slowing down at a rate of 3 rad/s^2.. knowing the wheel rolls without sliding and ignoring the effect of gravity determine the location on the wheel where the net acceleration is zero. Provide your answer in terms of x,y coordinates with 0,0 being at the wheel's center.

diameter =24in

Reference no: EM13557002

Questions Cloud

Calculate the moment of inertia of the hollow rectangular : A hollow rectangular steel beam is 18 cm deep by 10 cm wide, outside dimensions. The walls are 2 cm in thickness. From the shear and moment diagram, the maximum vertical shear on the section is 180 kN
Select the proper value of k so that the max deflection : While designing a shock absorbing bumper for a 5-Mg rail car, the spring used for the bumper follows a nonlinear relationship of F = ks2 where F is the force in Newtons and s is the compression distance in meters.
What is the magnitude of the maximum force acting on it : A 0.20 kg body undergoes simple harmonic motion of amplitude 9.7 cm and period 0.20 s. What is the magnitude of the maximum force acting on it
What is the magnitude of the electrons initial acceleration : A 30 feet column is braced at the mid-section to prevent premature failure. If the maximum load is 380 kips, select an appropriate W14 section, if any, to support the loading conditions.
Determine the location on the wheel where the net : A wheel rolls to the right with an angular velocity of 2 rad/s while slowing down at a rate of 3 rad/s^2.. knowing the wheel rolls without sliding and ignoring the effect of gravity
Obtain the angular frequency of the particle : A particle with a mass of 3.50 10-20 kg is oscillating with simple harmonic motion with a period of 3.50 10-5 s and a maximum speed of 1.50 103 m/s. Calculate the angular frequency of the particle
Find the maximum force exerted on the block : An oscillator consists of a block of mass 0.800 kg connected to a spring. When set into oscillation with amplitude 34.0 cm, it is observed to repeat its motion every 1.000 s. Find the maximum force exerted on the block
The connection is through the flange : Select an ST shape to be used as a 20-ft long tension member to resist the following service loads: Dead load=38kips live load=115 kips and snow load= 75 kips. The connection is through the flange with 3/4inch diameter bolts in each line. Use A572 Gr..
Estimate the magnitude of the acceleration of the box : A box mass 5.00 kg moves on a ramp that is inclined at 6.9° above the horizontal. A person is applying a constant force F=70.0 N to the box, What is the magnitude of the acceleration of the box

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the velocity of sphere a and wedge b immediately

At an angle of α=30°with the vertical, a 5kg sphere is suspended on a string of length .8m with a initial velocity of 1.2m/s, it colides with wedge B. ε=.7 between the .9kg wedge and sphere A.

  What is the pulling force to be applied for one of the plate

Due to temperature change, a 1/32" hole mismatching occurred. What is the pulling force, in lbs, to be applied for one of the plates to match the two holes The plate length is 3 ft (from the left end to the hole) and its cross section is 1/8" x 1"..

  Explain how to change the cell phone service

Plan 2 has a $40/month access fee, unlimited nights and weekends, 750 anytime minutes plus $0.29/minute for minutes over 750, text messages cost $0.05 each, and roaming cost $0.39/minute whenever she leaves the state.

  Explain how to draw v-t and x-t curves of industrial planer

The velocity of the bed is limited to a maximum value of 150 mm/s to the right and 300 mm/s to the left; the acceleration is successively equal to 150 mm/s^2 to the right, zero 150 mm/s^2 to the left, zero, etc.

  When the axial load p is applied show that the axial

The steel shaft of diameter D is cemented to the thin rubber sleeve of thick-ness t and length L. The outer surface of the sleeve is bonded to a rigid support.

  Determine the final volume of the gas in meter cube

A piston-cylinder assembly containing 1/4 kg of a gas undergoes a constant pressure process at 5 bar beginning with a specific volume of 20 m^3/kg. for the gas in the system the work is -15 kj. determine the final volume of the gas in m^3

  What is the min removal efficiency of the electrodialysis

An electrodialysis is used to treat a stream of 125 m3/d produced water with a salinity of 13,000 mg/L NaCl before the produced water is discharged to the river with the flow rate of 5 million L/d and salinity of 20 mg/L NaCl.

  Determine the coordinates of point e of the lot

Calculate the area of a piece of property bounded by a traverse and circular arc with the following coordinates at angle points: A (1275.11, 1356.11), B (1000.27,1365.70),C (1000.00, 1000.00),D (1450.00, 1000.00)

  Determine the volume of each cfstr

Disinfection by ozone follows first-order kinetics, with a rate constant of 1.2/minute. The town of Obfisquitory wishes to use 4 equal volumes of CFSTR's in series to disinfect 2 million gallons per day (mgd) of water containing 1000 coliforms/L to t..

  Determine the velocity of the cart while girls are walking

The 90-lb boy and 75-lb girl wald towards eachother with constant speed on a 330-lb cart with frictionless wheels. assume that the cart was at rest befor the boy and girl start walking.

  What is the distance traveled bythe collar upon release

A collar of weight m slideswithout friction on a horizontal rod between springs A and B. Thecollar is pushed to the left, compressing spring A 0.1 m. k of A is1.6 kN/m and k of B is 2.8 kN/m.

  Calculate the hydraulic conductivity of this clay

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm. Calculate the hydraulic conductivity of this clay.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd