Should the engineer use the un-identified material or the

Assignment Help Civil Engineering
Reference no: EM13544539

The modulus of elasticity of an un-identified metal is known to be 3000 ksi. An engineer has to design a rod with a fixed diameter to carry a load, P, and wishes to keep the deformations in the rod to a minimum. Should the engineer use the un-identified material or the steel with X ksi modulus of elasticity? Why? Show all of your calculations.

Reference no: EM13544539

Questions Cloud

Select a hydraulic pump size and a hydraulic cylinder size : An engineer is designing a hydraulic lift with a capacity of 10 tons. the moving parts of this lift weigh 1000lbf. the lift should raise the load to a height of 6ft in 20 seconds. This will be accomplished with a hydraulic pump
The given data show the result of a model known : The given data show the result of a model known as stopping sight distance, used by civil engineers to design roadways speed(mph) stopping sight distance(ft)
Design and detail the steel reinforcement for the section : The beam has a rectangular section which is to be singly reinforced. Given pt=1.1% design and detail the steel reinforcement for the section where the moment is maximum
To keep cells at 55 degrees : To keep cells at 55 degrees? Why or why not?
Should the engineer use the un-identified material or the : The modulus of elasticity of an un-identified metal is known to be 3000 ksi. An engineer has to design a rod with a fixed diameter to carry a load, P, and wishes to keep the deformations in the rod to a minimum.
What is the concentration of the mixture of the stream : Directly below the discharge point is a prime fishing spot and the fish are intolerant to salt concentrations above 200 mg/L. How much salt should be removed per day from the plant effluent stream in order to maintain a concentration of salt
What will be the ratio of the mass of natural gas : Natural gas is stored in a spherical tank at a temp. of10oC. At a given initial time, the pressure in thetank is 100 kPa gage, and the atmospheric pressure is 100 kPaabsolute
Explore the advantages and disadvantages of law making : Explore the advantages and disadvantages of law making
Determine the maximum height the projectile will reach : A projectile is fired up into the air at a speed of 161 m/s at an angle of 64° relative to the horizontal. Determine the maximum height the projectile will reach.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Differential settlement between the centre line of the ring

Determine the differential settlement between the centre line of the ring beam and under the centre of beam. The inner and outer radii of the ring beam are 8m and 12m respectively.

  The water temperature can be assumed to be 60 degrees

A gunite concrete trapezoidal channel with 1:2 side slopes, as ilustrated below, conveys 60 m3/s on a slope of 0.0005. Compute the depth of flow.

  You are the chief civil engineer for the enhanced

You are the Chief Civil Engineer for the Enhanced Protein Production Plant on the planet Zog where the gravitational constant is 15 ft/s2. A protein storage tank has developed a structural problem and must be drained. There is a 6 inch diameter orifi..

  Calculate the location of the effective depth on both sides

beam is 24 inch deep, the steel stirrup used is number 4,a 1 1/2 inch. concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth.

  Write a program that will ask for the part number

Write a program that will ask for the part number for two different parts (i.e. PX_12345, and ABC_329). Display these parts in ONE message box, in numerical order (i.e. the segment of the part number to the right of the underscore character).

  Explain why not use rubber to seal wine bottles

Cork is used for sealing sparkling wine bottles. Aside from friction, why not use rubberbto seal wine bottles. (Hint: think about the force exerted by the pressure inside and how does that deform each material) Be sure to use poissons ratio in the..

  Determine what is the radial-horizontal stress at the point

A tire carries a 5,000-lb load and has a pressure of 100 psi. The pavement has a modulus of elasticity of 43,500 psi. A deflection of 0.016 inches is observed at a point on the pavement surface 0.8 inches away from the tire load.

  Calculate what is the critical value for x in inches

When X exceeds some critical distance the slider will "lock" and no longer move regardless of the force applied. If the coefficient of friction for the slider bearing is 0.1, what is the critical value for X in inches

  Determine the pressure head at the nozzle inlet to produce

determine the pressure head at the nozzle inlet to produce a water jet velocity of 40 ft/s. Neglect the friction loss and assume incompressible flow.

  Determine the x-y and z components of reaction at the pin

The member is supported by a pin at A aand a cable BC. If the load at AD is 300 lb, determine the x,y,z components of reaction at the pin A and the tension in cable b c

  Determine what is the standard deviation in w given the fact

You arrive at your bus stop at some random point in the cycle, what is your expected wait time, w(t), to board a bus. Be sure to show your work or you will lose points. What is the standard deviation in w(t) given the fact that there is no bus wait..

  Imaging you have to shoot a basketball ball

Part B (Assignment): by trial and error, find the angle that will give the minimum force F to make a basket (hint: try 52 degrees)The trajectory of the ball will make a basket when x = L and y = Hb

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd