Select a hydraulic pump size and a hydraulic cylinder size

Assignment Help Civil Engineering
Reference no: EM13544543

An engineer is designing a hydraulic lift with a capacity of 10 tons. the moving parts of this lift weigh 1000lbf. the lift should raise the load to a height of 6ft in 20 seconds. This will be accomplished with a hydraulic pump that delivers fluid to a cylinder. Hydraulic cylinders with a stroke of 72 inches are available with bore sizes from 2 o 8 inches. Hydraulic piston pumps with an operating pressure range from 200 to 3000 psig are available with pumping capacities of 5, 10, and 15 gallons per minute. Select a hydraulic pump size and a hydraulic cylinder size that can be used for this application.

Reference no: EM13544543

Questions Cloud

How far from shore is a sailboat when the top of its 8m : How was this answered reached? what equation was used? equation of a line? could you please explain how the answer was reached and a detailed explanation of the math behind it.
Determine the youngs modulus of the steel alloy and the : a round steel alloy bar with a diameter of 0.75 in and a gauge length of 3.0 in was subjected to tension, with the results shown in the accompanying table. using a computer spread sheet program
Determine the braking efficiency of car : Two cars are traveling on level terrain at 60 mi/h on a road with a coefficient of adhesion of 0.8. The driver of car 1 has a 2.5-s perception/reaction time and the driver of car 2 has a 2.0-s perception/reaction time
What is the shortest height it should be : An engineering student has been given the assignment of designing a hydraulic holding system for a hay baling system. The system has four cylinders with 120 mm diameter pistons with a stroke of 0.320 m
Select a hydraulic pump size and a hydraulic cylinder size : An engineer is designing a hydraulic lift with a capacity of 10 tons. the moving parts of this lift weigh 1000lbf. the lift should raise the load to a height of 6ft in 20 seconds. This will be accomplished with a hydraulic pump
The given data show the result of a model known : The given data show the result of a model known as stopping sight distance, used by civil engineers to design roadways speed(mph) stopping sight distance(ft)
Design and detail the steel reinforcement for the section : The beam has a rectangular section which is to be singly reinforced. Given pt=1.1% design and detail the steel reinforcement for the section where the moment is maximum
To keep cells at 55 degrees : To keep cells at 55 degrees? Why or why not?
Should the engineer use the un-identified material or the : The modulus of elasticity of an un-identified metal is known to be 3000 ksi. An engineer has to design a rod with a fixed diameter to carry a load, P, and wishes to keep the deformations in the rod to a minimum.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Compute the flows with return periods of 1 5 and 15 years

The table below provides the flows for the Llano River in Texas for the period of 1951 to 1970. Using the simplified frequency analysis method show in class (Weibul method)

  Estimate the discharge rate of the pipeline

Reservoir A (water surface elevation = 1300 ft) is connected to reservoir B (water surface elevation=250 ft) by 6,000 ft of 14 inch diameter cast iron pipe (e = 0.005 ft. Neglecting all minor losses

  What is the force between the bar and block d

Block D sits freely on the homogeneous bar and experiences a gravitational force of 50N. Homogeneous bar AB experiences a gravitational force of 25 N. What is the force between the bar and block D?

  Calculate what is the porosity of the sand

You have a beaker filled with coarse sand. The capacity of the beaker is 100cm^3. Next, you add to the beaker 40cm^3 of distilled water, filling the water level exactly to the top of the sand.

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  What would be the capillary pressure between oil

Assume that the interfacial tension between oil-water is 22 dynes/cm and the contact angle through water is 93

  Calculate total metabolic heat generated by a singing canary

calculate the total metabolic heat generated by a singing canary taking into account heat transfer by radiation, convection and exhaling air. The air temperature is 20`C, canary's body internal and surface temperature is 33`C

  How to calculate the asphalt content by weight of mix

The VMA of a mixture is 15.0% and the air voids are 4.0%.If the aggregate has a specific gravity (bulk dry) of 2.700 g/cm3 and percent binder absorbed (by the mass of aggregate) is 0.5%, calculate the asphalt content by weight of mix.

  Determine the angular speed n of the wheel of the rim

The cart has a velocity of 4 ft/sec to the right. Determine the angular speed N of the wheel so that point A on the top of the rim has a velocity (a) equal to 4 ft/sec to the left, (b) equal to zero, and (c) equal to 8 ft/sec to the right

  Determine the maximum torsional stress in the shaft and its

The propellers of a ship are connected to an A-36 steel shaft that is 60m long and has an outer diameter of 340mm and inner diameter of 260mm

  If the bar is reloaded then what is the proportional limit

A circular bar of magnesiuen alloy is 750 mm long. The bar is loaded in tension to an elongation of 6.0 mm, and the load is removed. (a) what is the permanent set of the bar (b) if the bar is reloaded, what is the proportional limit

  What is the max price per ton the company should pay

The supplier says it would prefer to sell the company a 65% NaOH solution and the company says the water content is immaterial as long as the equivalent costs are the same including freight.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd