Problems were found in the use of precast concrete

Assignment Help Civil Engineering
Reference no: EM13900247

Problems were found in the use of precast concrete, is:
A. Need a larger initial investment
B. Requires fabricating a very wide area
C. Need more manpower
D. Must be close to the installation location

Reference no: EM13900247

Questions Cloud

Discuss whether lee garrett was acting in an ethical manner : Discuss whether Lee Garrett was acting in an ethical manner. How might Guardsman Security Co. use internal controls to prevent this scenario from occurring?
The percent voids in the sand : If a mortar is proportioned to 0.11 ft3 of cement, 0,03 ft3 of lime, 0.27 ft3 of water, and 0.50 ft3 of sand, the percent voids in the sand is? (Assume a sand Bulk Specific Gravity Oven-dry of 2.60; of cement 3.15, and lime 2.25 if needed).
The advantages of using precast floor slab half : The advantages of using precast floor slab half is:A. Reducing the volume of concrete
Give atleast three methods : Give atleast three methods that can be use to analyse structures
Problems were found in the use of precast concrete : Problems were found in the use of precast concrete, is:A. Need a larger initial investmentB. Requires fabricating a very wide area
Determine ratio of cash to monthly expenses as of december : Determine the ratio of cash to monthly expenses as of December 31, 2004, 2003, and 2002. Round to one decimal place. Based upon (1) and (2), comment on OccuLogix's ratio of cash to monthly operating expenses for 2004, 2003, and 2002.
Below are some of the advantages of using precast : Below are some of the advantages of using precast (precast concrete), except:A. The timing of the shorterB. Control of technical quality can be achieved
Describe the role of the information technology professional : Describe the role of the information technology professional and develop an information technology strategic plan to address and solve a proposed business problem.
The comments and critique are concise and error-free : Ensure both the comments and critique are concise and error-free.

Reviews

Write a Review

Civil Engineering Questions & Answers

  How to estimate for the loaded machines on level ground

Stripping overburden in the Illinois coal belt, the Dusty Coal Company uses 270-horsepower, track-type tractors (with direct-drive transmissions) and drawn scrapers.

  Determine the pressure in the tank indicated by a strain

A single strain gage forming an angle B = 18 degrees with a horizontal plane is used to determine the gage pressure in a cylindrical steel tank. The cylindrical wall of the tank is 6mm thick, has a 600mm inside diameter

  Determine particles position and the velocity of particles

The acceleration of a particle along a straight line is defined by a=(2t-9)m/s^2, where t is in seconds.At t=0, s=1m, and v=10 m/s. When t=9s, determine the particles position, the total distance traveled, and the velocity.

  Determine the shear-thrust and moment in the arch at point c

The three hinged arch is composed of segments of a circle. Support points A and D are not at the same level.Determine: (a) the horizontal and vertical components of reaction at A and D.

  The mechanical properties of aluminum may be improved

The mechanical properties of aluminum may be improved by incoporating fine particles of lauminum oxide (al2O3) Given that the moduli of electricity of this material are respectively 69GPa and 393 GPa plot modulus

  What is overall specific gravity of sample initially package

What is the overall specific gravity of a sample initially packaged with a moisture content of 3.5% below the optimum, then saturated (Assume that the soil sample can be compressed fully saturated with water without the occurrence of variation in ..

  Determine what will be the total settlement of a laboratory

The settlement of a laboratory 10-cm thick consolidation specimen is 5 mm in 1 hour with a coefficient of consolidation of 0.005cm2/s. What will be the total settlement

  By what percentage is the capacity of the flume reduced

determine the width of the flume to be used such that the depth of flow immediatly upstream of the throat under design conditions is 1 m. By what percentage is the capacity of the flume reduced if the downstream depth is 0.85m

  What is the time elasticity of demand when t=2 minutes

Latent demand for highway travel is defined as the differencebetween the maximum numver of trips that could be made and thenumber of trips that are actually made. given a demandfunction:

  What next job or promotion do you want

What next job or promotion do you want? (your choice of realistic or ‘dream job') ,How would you describe this job? (try searching for legitimate job descriptions) and What attracts you to this job?

  Determine the total deformation of composite rod abc

two solid cylindrical rods are joined at B and loaded as shown rod AB is made of steel(E=200 GPa) and rod BC of brass ( E = 105GPa) determine a) the total deformation of composite rod ABC, b) the deflection of point B

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd