Plot the two test results on a shear stress-normal stress

Assignment Help Civil Engineering
Reference no: EM13552821

Two triaxial tests were performed on two prepared samples of the same limestone. At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi, the other sample failed at 21,000 psi. Plot the two test results on a shear stress-normal stress diagram and draw in Mohr envelope.

Reference no: EM13552821

Questions Cloud

The treaty and accompanying implementing legislation : The treaty and accompanying implementing legislation were approved
Determine the isentropic compressor efficiency : Refrigerant 134a enters the compressor of a vapor compression heat pump at 15 psi and 0 °F and is compressed to 160 psi and 160 °F. Liquid enters the expansion valve at 160 psi and 95 °F. At the valve exit the pressure is 15 psi.
Determine the vertical stress increment due to the strip : Determine the vertical stress increment due to the strip load and the total pressure both at point 3 m below the center of the strip load.
Increase the level of economic and social integration : Increase the level of economic and social integration
Plot the two test results on a shear stress-normal stress : Two triaxial tests were performed on two prepared samples of the same limestone. At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi
Prepare adjusting entries for estimated depreciation : Prepare adjusting entries for Estimated depreciation - An examination of insurance policies shows $890 of insurance expired.
How long do you have to escape : You are in an old spy movie, and have been locked into a small room (volume 1000 ft). You suddenly realize that a poison gas has just started entering the room through a ventilation duct. Recognizing the type of poison from its smell, you know that i..
What is the peak discharge at the reach outlet : Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.
Post-closing trial balance for cruz company : Prepare the December 31, 2013, post-closing trial balance for Cruz Company - Prepare the December 31, 2013, closing entries for Cruz Company.

Reviews

Write a Review

Civil Engineering Questions & Answers

  The first one is a plug flow reactor with a residence time

Plot the concentration of tracer at the outlet of the each of the two reactors during the first 24 hours of the tracer study. (Hint: You may need to use mass balances to obtain equations that predict the concentration of tracer as a function of time)

  Determine the location e of the shear center

Determine the location e of the shear center, pt. O, for the thin-walled member having the cross section shown. The member segments have the same thickness t.

  Determine the resulting velocity of center of the cylinder

a 9in radius cylinder of weight 18lb rests on a 6lb carriage. the system is at rest when a force p of magnitude 2.5 lb is applied ( p is coming out of the car the cylinder is sitting on and going to the right) for 1.2s.

  Determine the dimensions of the best hydraulic trapezoidal

Determine the dimensions of the best hydraulic trapezoidal concrete channel section to convey water at a rate of 2200 gal per min on a channel slope of 0.015 m/m.

  Question 1 ndash the pipe shaft of the auger rotating at a

question 1 ndash the pipe shaft of the auger rotating at a constant angular velocity is subject to the axial force and

  Determine the factor of safety of this trench by the culman

A 1.5 meter deep vertical wall trench is to be cut in a soil whose unit weight is 17.36 kN/cubic meters, angle of internal friction is 25 degrees, and cohesion is 20.6 kN/square meters. Determine the factor of safety of this trench by the Culmann Met..

  Describe the ductility of a reinforced concrete beam

What does under-reinforced mean Which is desirable and why How would your Moment-Curvature plot be affected if the amount of tension steel was doubled How would your Moment-Curvature plot from part a be affected if compression steel was added to the..

  Determine the adequacy of the design using basic principles

For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.

  What are the basic assumptions of the traffic flow model

What are the basic assumptions of the 'traffic flow model' and 'capacity model' used in signal timing design. Discuss.

  What is the absolute pressure within the tank

If the atmospheric pressure is 14.20 psia and a gage attached to a tank reads 12.5 inHg vacuum, what is the absolute pressure within the tank

  What type of contract would you want and why

If you were asked to perform an excavation contract competitively with limited data, what type of contract would you want and why?

  Find what flow of water in gallons per second is required

The volume of water in a reservoir is often expressed using the unit of acre-foot. A volume of 1 acre-foot is the amount of water covering an area of 1 acre to a depth of 1 foot. Lake Mead is the largest man-made lake in the United States.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd