Determine the vertical stress increment due to the strip

Assignment Help Civil Engineering
Reference no: EM13552823

1.Workers new to carburetor assembly take 15 minutes to complete their first assembly. Assuming a 95 percent learning curve, how long would it take them to reach a standard time of 10 minutes?

2.Soil with a unit weight of 19.65 kN/m^3 is loaded on the ground surface by a strip load of 1.5 m wide. The strip load is 365 kN/m of wall length. Determine the vertical stress increment due to the strip load and the total pressure both at point 3 m below the center of the strip load.

Reference no: EM13552823

Questions Cloud

What will be the manometer deflection : The pressure inside a 4 cm hose is 700 kPa. If the water exits through a 2 cm diameter nozzle, what velocity in m/s, can be expected inside the hose ?
Determine the maximum permissible torque tmax : The composite shaft is made of a steel sleeve, which is bonded to a brass core. The outer diameters of the two parts are d1 = 40 mm for the brass core and d2 = 50 mm for the steel sleeve.
The treaty and accompanying implementing legislation : The treaty and accompanying implementing legislation were approved
Determine the isentropic compressor efficiency : Refrigerant 134a enters the compressor of a vapor compression heat pump at 15 psi and 0 °F and is compressed to 160 psi and 160 °F. Liquid enters the expansion valve at 160 psi and 95 °F. At the valve exit the pressure is 15 psi.
Determine the vertical stress increment due to the strip : Determine the vertical stress increment due to the strip load and the total pressure both at point 3 m below the center of the strip load.
Increase the level of economic and social integration : Increase the level of economic and social integration
Plot the two test results on a shear stress-normal stress : Two triaxial tests were performed on two prepared samples of the same limestone. At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi
Prepare adjusting entries for estimated depreciation : Prepare adjusting entries for Estimated depreciation - An examination of insurance policies shows $890 of insurance expired.
How long do you have to escape : You are in an old spy movie, and have been locked into a small room (volume 1000 ft). You suddenly realize that a poison gas has just started entering the room through a ventilation duct. Recognizing the type of poison from its smell, you know that i..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the estimated uncertainty in the length of vector

The base line vector between the base and roving reciever is 8340m and has an accuracy of +/-(1to 2 cm +/-2ppm). What is the estimated uncertainty in the length of this vector

  What is the distance uncertainty at the surface of ellipsoid

if a hand-held GPS unit locates a latitudinal position with an uncertainty of + - 0.02-seconds, what is the distance uncertainty at the surface of the ellipsoid.

  Proprietorships and last year gross profit

Jack Flubber, who owns sons of Flubber Construction Co. and runs it as a proprietorships had gross profit last year of $ 80000. His personal and family expenses are $ 52000 and he has $ 7000 in exemptions and deductions.

  Ultimate load for a strip footing under long-term

Show that the ultimate load for a strip footing under long-term conditions using the two triangle failure surfaces

  Compare three-decimal-place values of two approximations

Compare the three-decimal-place values of the two approximations at x=(1/2) with the value y(1/2) of the actual solution . then do the same for PART B: y'=-2xy , y(0)=2 ; y(x)=2e^(-x^2)

  Calculate 5 day cbod of the river after mixing with waste

An industry discharges .5m^3/s of waste with a 5 day CBOD of 500 mg/l to a river with a flow of 2 m^3/s and a 5 day CBOD of 2 mg/l calculate the 5 day CBOD of the river after mixing with the waste.

  What is the difference in water levels between reservoirs

A wrought iron water line connecting two reservoirs at 20°C has a length of 1500 m, a diameter of 75 cm, two elbows (90º, long-radius, flanged), a fully open gate valve, and a reentrant pipe entrance.

  Solve a linear program that will suggest a hen managentment

Assume that an egg can be hatched only in the week after it is laid. Otherwise it must be saved and sold for 10 cents. Assume that there are no eggs available for hatching in the first week.

  Compute how many grams of water must be added to soil

it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1000g of soil( in its natural state) in order to increase the water content 2..

  What is overturning factor of safety for building wind load

How many floors can be added to the building while maintaining the code required overturning factor of safety of 2.0 Assume the roof supports a wind load of 4 kips and all floors below support a wind load of 8 kips.

  Check the shear resistance of the beam use asd design method

The beam is loaded with a concentrated live load of 10 kips at the center of its span, in addition to its own weight.. The dead load includes the beam weight. The steel is A242, Grade 50.

  Find the amount the company must deposit each year

If a company wants to have $100,000 in a contingency fund 10 years from now, the amount the company must deposit each year in years 1 through 5, at an interest rate of 10% per year, is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd