Plot the two test results on a shear stress-normal stress

Assignment Help Civil Engineering
Reference no: EM13316935

Two triaxial tests were performed on two prepared samples of the same limestone. At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi, the other sample failed at 21,000 psi. Plot the two test results on a shear stress-normal stress diagram and draw in Mohr envelope.

Reference no: EM13316935

Questions Cloud

What frequency do you hear after it passes by you : A police car is moving towards you at a speed of 36.0 m/s. Its siren produces a frequency of 850 Hz. What frequency do you hear after it passes by you
Determine the axial forces in the members of the truss : A cable is attached at A and is connected to the wall. Determine the axial forces in the members of the truss using the Method of Joints and indicate whether they are in tension (T) or compression (C). Be sure to provide complete free body diagram..
How far away was the lightning bolt : Thunder is heard 4.0 sec after the flash of lightning is observed. If the outside temperature is 15 degrees celsius, how far away was the lightning bolt
Advise periwinkle of its fbt consequences arising out : Advise Periwinkle of its FBT consequences arising out of the above information, including calculation of any FBT liability, for the year ending 31 March 2014 and how would your answer to (a) differ if Emma used the $50,000 to purchase the shares h..
Plot the two test results on a shear stress-normal stress : At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi, the other sample failed at 21,000 psi. Plot the two test results on a shear stress-normal stress diagram and draw in Mohr envelope.
Calculate his break shot speed : the top of a pool table is 0.770 m from the floor. the placement of the tape is such that 0 m aligns to the edge of the table. calculate his break shot speed
How many holes are required to break 250000 tons : Conduct a powder factor design for the following conditions: -Rock is iron ore; density is 5370 lb/cubic yards -Rock swells 60% from in situ when broken -Bench height is 45ft -Drill hole diameter is 12.25 inches
Determine the increase in length of the wire : A wire is 1.50 m long and has a diameter of 1.50 mm. The tensile modulus of the wire is 6.20 x 1010 N/m2. what is the increase in length of the wire
Calculate the axial and radial strains and volumetric strain : A cylindrical soil, 75mm in diameter and 150 mm long, is radially compressed. The length increases to 153 mm and the radius decreases to 37.2 mm. Calculate: a) The axial and radial strains b) The volumetric strains

Reviews

Write a Review

Civil Engineering Questions & Answers

  What will be the surface tension effects for the tube

A water column in a glass tube is used to measure the pressure in a glass pipe. The tube is 1/4 in. in diameter how much of the water column is due to the surface tention effects

  Determine the speed with which b must walk toward a

Swimmer A immediately starts walking toward B at a speed of 2ft/s relative to the raft. Knowing that the raft weighs 300 lb, determine (a) the speed of the raft if B does not move, (b) the speed with which B must walk toward A

  Estimate the theoretical production of landfill gas

estimate the theoretical production of landfill gas (CH4 only) from the degradation of 20.3 kg of rapidly decomposable MSW. asssume the density of methane is 0.7177 kg/m^3.

  Determine the time required for a car to travel 1 km

Determine the time required for a car to travel 1 km along a road if the car starts from rest, reaches a max speed at some intermediate point, and then stops at the end of the road. the car can accelerate at 1.5 m/s^2 and decelerates at 2 m/s^2

  Determine the diameter of the pipe to be maintained in pipe

A flowrate of 3.5 ft^3/s is to be maintained in a horizontal aluminum pipe ( E = 5 * 10 ^-6 ft). The inlet and outlet pressures are 65 psi and 30 psi, respectively, and the pipe length is 500ft. Determine the diameter of the pipe.

  Determine the uniform flow depth in a rectangular channel

Determine the uniform flow depth in a rectangular channel 2.5 m wide with a discharge of 3 m3/s. The slope is 0.0004 and Manning's roughness coefficient is 0.015

  What is maximum acceleration from rest for car with engine

The car weights 2450 lb, the mechanical efficiency of the drivetrain is 90%, and the wheel radius is 14 inches. The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque.

  Determine what is the elevation of the point b

Long Line: the slope distance and zenith angle measured from point a to point b were 17,685.20 ftand 93degrees 13' 46" . The instrument and reflector heights were equal. If the elevation of the point A is 1854.43 ft above the MSL Datum

  Determine the critical path-starting and finishing times

Activity Description Duration Immediate Predecessors ST Start milestone - Activity Description duration Inmdiate predesesor ST Start milestone - - A excavate st. 1 4 ST B Order & steel del. work 7 ST C Formwork st.

  Determine the deflection of a simple uniformly loaded

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  What is the stress in the lowermost rock

The Washington Monument is 169 m tall. What is the stress in the lowermost rock if it is made of Georgia granite?

  Determine what is the probability that all eight bits are 1

In a random pattern of eight bits used to test a micro-circuit, each bit is equally likely to be 0 or 1. Assume the values of the bits are independent. a. What is the probability that all eight bits are 1

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd