Calculate the axial and radial strains and volumetric strain

Assignment Help Civil Engineering
Reference no: EM13316931

A cylindrical soil, 75mm in diameter and 150 mm long, is radially compressed. The length increases to 153 mm and the radius decreases to 37.2 mm. Calculate: a) The axial and radial strains b) The volumetric strains

Reference no: EM13316931

Questions Cloud

Plot the two test results on a shear stress-normal stress : At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi, the other sample failed at 21,000 psi. Plot the two test results on a shear stress-normal stress diagram and draw in Mohr envelope.
Calculate his break shot speed : the top of a pool table is 0.770 m from the floor. the placement of the tape is such that 0 m aligns to the edge of the table. calculate his break shot speed
How many holes are required to break 250000 tons : Conduct a powder factor design for the following conditions: -Rock is iron ore; density is 5370 lb/cubic yards -Rock swells 60% from in situ when broken -Bench height is 45ft -Drill hole diameter is 12.25 inches
Determine the increase in length of the wire : A wire is 1.50 m long and has a diameter of 1.50 mm. The tensile modulus of the wire is 6.20 x 1010 N/m2. what is the increase in length of the wire
Calculate the axial and radial strains and volumetric strain : A cylindrical soil, 75mm in diameter and 150 mm long, is radially compressed. The length increases to 153 mm and the radius decreases to 37.2 mm. Calculate: a) The axial and radial strains b) The volumetric strains
What is the charge on each ball : Two balls of identical mass of 0.151 kg and with identical charges placed on them hang from the ceiling on identical strings of lengths 1.510 m, what is the charge on each ball
What is the area of the input piston : A hydraulic lift is used to jack a 970 kg car 12 cm off the floor. The diameter of the output piston is 18 cm, and the input force is 250 N. What is the area of the input piston
Find will the diver sink or float : A scuba diver and her gear displace a volume of 65 L and have a total mass of 68 kg. Will the diver sink or float
What is the diameter of a circular concrete column needed : What is the diameter of a circular concrete column needed to support a load of 300,000 pounds with a factor of safety of 2. Round the diameter up to the whole inch. The concrete ultimate strength is 3000 lb/in^2.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the minimum distance from the stalled car

What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitting it? Assume coefficient of rolling resistance of 0.013.

  Find modulus of elasticity of pavement for corner deflection

The pavement is on a base which has a modulus of subgrade reaction of 250 pci. A 17,000 lb corner load is applied (al is 7 inches). Using the revised Westergaard equations, find the modulus of elasticity of the pavement if a corner deflection of 0..

  Estimate the density of the air at an elevation of 10 km

Titan, a moon of Saturn, is believed by astronomers to have an atmosphere that is about 95% nitrogen. At Titan's surface the acceleration due to gravity is 1.35 m/s2, the atmospheric pressure is 210 kPa, and the temperature is 94 K.

  Determine what is the resulting solids concentration

Raw primary sludge at a solids concentraion of 4% is mixed with waste activated sludge at a solids concentration of .5%. The flows are 20 and 24 gal/min respectively. What is the resulting solids concentration

  What is the level of service expected in each direction

A Class I rural highway segment of 10 miles in level terrain has a base free-flow speed (BFFS) of 65 mph. The cross section has 12-ft lanes and 6-ft clear shoulders on both sides of the road.

  Determine the safe load the column can carry using method

A column of dimensions 200 X 300 mm has an effective length of 3m. It is reinforced with 6 HYSD bars of 20mm diameter. Determine the safe load the column can carry using working method of design. Using M20 Concrete.

  Find the soil parameters-saturated unit weight

A soil has a total density of 1.80 Mg/m3. When fully dry, the soil has a density of 1.59 Mg/m3. The specific gravity of the solids is 2.57. Find the following soil parameters: a) Dry unit weight of the sample

  Calculate the factor of safety and deformation

A 1 cm diameter, 0.4 m long steel rod is to be used in an application where it will be subjected to an axial tensile force of 15kN. The factor of safety based on yield stress must be at least 1.5, and the axial deformation must not exceed 2 cm.

  Determine the density of the air in a laboratory

Some experiments are being conducted in a laboratory in which theair temperature is 26o C and the atmosphericpressure is 14.6 psia. Determine the density of the air.Express your answers in slugs/ft3 andkg/m3.

  Bernoulli equation-measure the flow rate through the meter

The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.

  Coefficient of curvature for each soil

Determine the effective size as well as the uniformity coefficient and coefficient of curvature for each soil. Determine also the percentages of gravel, sand, silt, and clay according to (a) ASTM, (b) AASHTO, (c)USCS, and (d) the British Standard.

  Find the correction for the calibration of the measuring tap

Find the correction for the calibration of the measuring tape using its formula. During the calibration of the measuring tape on comparator of 100.000m the length of the tape turned out to be of 99.993m

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd