Plot the mohr circles for both failure stress conditions

Assignment Help Civil Engineering
Reference no: EM13542365

A conventional consolidated drained (CD) triaxial test is conducted on sand. The cell pressure is 100 kPa, and the applied axial stress at failure is 200 kPa.

Required:

a. Plot the Mohr circles for both (1) initial and (2) failure stress conditions.

b. Determine Phi (assume c=0)

c. Determine (3) the shear stress on the failure plane at failure Tao,ff and find (4) the theoretical angle of the failure plane in the specimen.

d. Determine (5) the maximum shear stress at failure Tao,max and (6) the angle of the plane on which Tao,max acts; calculate (7) the available shear stress on the plane.

e. Calculate factor of safety (F.S.) on (8) the plane of Tao,max and (9) the failure plane.

Reference no: EM13542365

Questions Cloud

Assigning the central pier and the abutment as fixed : Design a 300 + sl m long variable graded terrace for a land having an average slope of 2 %. Maximum permissible velocity of water in the terrace channel is 60 cm/sec. The most sever rainfall expected in 10 yr RI has an intensity of 9 cm/hr.
Determine the components of the reaction at point c when the : The object ABC consists of two slender rods welded together at point B. Rod AB has a mass of 1 kg and bar BC has a mass of 2 kg. Knowing the magnitude of the angular velocity of ABC
How should the guided bearings in piers of the curved region : In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?
How do you determine the cross-sectional area of the concret : How do you determine the cross-sectional area of the concrete and steel and the stresses in each if the column deforms .01 inch while carrying 100 K load? The cross sectional area is 15 inch and column height is 10 feet.
Plot the mohr circles for both failure stress conditions : Determine (5) the maximum shear stress at failure Tao,max and (6) the angle of the plane on which Tao,max acts; calculate (7) the available shear stress on the plane.
Draw the idealized stress-strain diagram for a material : Write out the final version of Hooke's Law which includes Young's Modulus. Draw the idealized Stress-Strain diagram for a material. On the drawing, please label: the yield stress, the plastic deformation, and the yield strain.
Determine the velocity of the collar at point b for any give : Knowing that the collar is releasted from rest at A, develop an equation to determine the velocity of the collar at point B for any given value of k (k-range is 0.1-2.0 lb/in)
Compute the sorbed concentration in equilibrium with the : If the pH of the water is raised to 8.5, what is the equilibrium concentration of the chromium (III) in moles/L? (d) What weight (in pounds) of precipitate is formed if groundwater containing 19,000 mg/L chromium is treated as described in part (c) a..
Rappahannock above the point where the two streams mix : The Rappahannock River near Warrenton, VA has a flow rate of 3.00 cms. Tin Pot Run (a pristine stream) discharges into the Rappahannock at a flow rate of 0.05 cms

Reviews

Write a Review

Civil Engineering Questions & Answers

  Draw a small sketch that shows a situation

Name three types of metamorphic foliations, and draw a small sketch that shows a situation where a metamorphic foliation could cause problems in an excavation.

  Draw the stress strain diagram using scales of 1

a concrete cylinder having a diameter of 6 in and a gauge length of 12 in is tested in compression the results of the test are reported in the table as load vs contraction. Draw the stress strain diagram using scales of 1 in=.5ksi

  Determine the specific volume of the exit stream

A stream of Refrigerant-134a at 1 MPa and 12 C is mixed with another stream at 1 MPa and 60 C. If the mass flow rate of the cold stream is twice that of the hot one, determine the specific volume of the exit stream.

  Compute stationing of pvc-pvi and pvt curve points

The profile of the bridge and tunnel. Devise a vertical alignment to connect the tunnel and bridge by determining the highest common design speed for the sag and crest (equal tangent) vertical curves needed.

  What weight can it bear before being broken

A concrete sidewalk slab is 17.5 MPa, 4 inches deep, and 2 m long.  A tree root has pushed it up so there is a 1 inch lip at the junction with the adjacent slab, and the slab is effectively 1 inch above its base underneath

  What amount must jackie invest over the next 15 years

Jackie is now exactly 40 years old, and plans to invest a recurring amount over the next 15 years (until age 55) in an account bearing 10% annual interest. She plans to retire at age 65 and live to age 100 (don't we all).

  Find the maximum deflection of a wooden bearer

Find the maximum deflection of a wooden bearer which has three supports; one at each edge (2) and one in the middle (2m from each other). Bearer holds a UDL over its whole length (4m) of 600 N/m.

  Calculate air flow required in cfm to transfer in hvac duct

Calculate the Air flow required in CFM to transfer 5,004 BTU/Hour in an HVAC duct given that the temperature difference (Delta-T) between the room and the supply air is 23 DegF.

  Determine time of flight when it return to original position

A ball is thrown vertically upward with a speed of 15m/s. Determine the time of flight when it returns to its original position.

  How many metric tons per day of nox are emitted

A coal-fired power plant produces a net electrical output of 500 MW. The composition of the coal burned is C= 72 %, H= 6 %, S= 3.5 %, O= 6 %, N= 1 %, and ash= 12 % by weight. It's heating value (HV) is 30200 kJ/kg. The net thermal efficiency is 36..

  Determine the depth of flow at the transition at a depth

A 1.6-m wide rectangular channel carries 1.8 m3/s at a depth of 0.85 m. The channel undergoes a smooth transition in which the channel bottom rises 15 cm and contracts to a width of 1.3 m. Assuming friction losses are negligible, determine the dep..

  Determine the values of speed and oncentration at capacity

A study of the traffic using a tunnel showed that the following speed-concentration relationship applies. Find the capacity of the tunnel, the values of speed and oncentration at capacity, and the jam concentration.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd