How would you measure the bandwidth of a dc amplifier

Assignment Help Electrical Engineering
Reference no: EM131282466

1. How would you measure the bandwidth of a dc amplifier?

2. Why does the decibel voltage gain use a factor of 20 but the power gain uses a factor of 10?

3. Why is impedance matching important in some systems?

4. What is the difference between dB and dBm?

Reference no: EM131282466

Questions Cloud

Health information technology to address the continuum : Final Project: Health Information Systems: Recommendation for the Acquisition, Implementation, and Support of a Health Information System PowerPoint Presentation: Health Information Technology to Address the Continuum of Care
Why is a dc amplifier called a dc amplifier : A radio station engineer needs to test the voltage gain over several decades. What type of graph paper would be most useful in this situation?
Discuss a successful project and an unsuccessful project : Identify and discuss a successful project and an unsuccessful project with which you are familiar. Include what you would say distinguishes the two, both in terms of the process used to develop them and their outcomes?
Interview a human resource manager : You are required to interview a human resource manager, or someone who has responsibility for human resource management in an organisation. The assessment should also include a literature review on the role and activities of good people management..
How would you measure the bandwidth of a dc amplifier : Why does the decibel voltage gain use a factor of 20 but the power gain uses a factor of 10?
Draw the ideal bode plot for the input lag circuit : Assume that the front panel of your oscilloscope notes that its vertical amplifier has a risetime of 7 ns. What does this say about the bandwidth of the instrument?
How did blackberry launch its new product : I need one summary slide, and only one point of view on slide 2. How did blackberry react to apple-how did apple break the rules? How did blackberry launch its new product?
Announcement by general mills : This is a question in Marketing.... Read the following announcement by General Mills and respond to the questions below -
Patient decides to disconnect : Since the hospital/patient relationship is considered a contract of sorts, how is it affected if the patient decides to disconnect himself from telemetry and leave the hospital for 4 hours to go score some cocaine on the street? What would you do ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What would have to be added to the circuit

How could the string of numbers in the binary system be represented by means of DASYLab? What would have to be added to the circuit in Illustration 184.

  What relation should 2-parameters satisfy to maintain output

A repeater has an input signal of 150μW and an output signal-noise ratio of 20 dB. The repeater has a gain of A and additional noise of N. What relation should the two parameters satisfy to maintain an output noise figure less than 2 dB

  What form of linear distortion is introduced by the channel

Two components of linear distortion produced by transmitting asignal through an LTI (linear time invariant) system: Amplitude distortion - the frequency components of the input signalare transmitted through the system with different amounts of gain..

  How much energy is dissipated in the resistor in 5 s

An AC source which produces a peak voltage of 169.7 V is connected across a resistor of 10 Ω. How much energy is dissipated in the resistor in 5 s?

  What is the relationship between torque

What is the relationship between Torque and armature current in DC shunt motor.

  What is the loss in each part if a second mosfet is added

A MOSFET is used in a boost-buck converter. The on-state loss is 4.2 W, and the switching loss is 2.8 W. The device is in TO-220 heat-sink package. it is desired to avoid a heat sink, and a parallel connection has been suggested.

  Determine the armature-developed power pdev

A 600V, 150hp, DC series motor operates at it's full-ratedload at 600 RPM. The armature resistance is 0.12 ohms and the series field resistance is 0.04 ohms. The motor draws 200A at full load.

  Find the disruptive critical voltage for the line

A 3-phase line has conductors 2 cm in diameter spaced equilaterally 1 m apart. - If the dielectric strength of air is 30 kV (max) per cm, find the disruptive critical voltage for the line.

  What is the characteristic impedance of a coaxial cable

What is the characteristic impedance of a coaxial cable that has an inner conductor diameter 0.108 in, an outer conductor diameter of 0.350 in, and a relative dielectric constant of 2?

  Calculate the line-to-line voltage at the load terminals

A delta connected load consists of three identical impedances Z=45 at 60 degrees per phase. It is connected to a three phase, 208-V source by a three phase feeder with conductor impedance Zfeeder=(1.2+j1.6) Ohms per phase.

  Write short little code fragments to add two 16-bit numbers

One of the ways to look at programming at the assembly-language level is to consider it as putting together code fragments that do various little jobs. (This is a little higher-level than just thinking of it as a sequence of machine instructions.)

  What is the resistance at100 degree centigrade

The resistance of a copper wire at 30oCis 50Ω. if the temperature coefficient of copperat 0oC is 0.00427, what is the resistance at100oC

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd