How much heat is required to vaporize the steam

Assignment Help Chemical Engineering
Reference no: EM131157636

The water gas shift reaction equilibrates rapidly at temperatures above about 450 °C. At high temperatures this reaction favors the formation of carbon monoxide, while at low temperatures more hydrogen is formed. When hydrogen is the desired product, the shift reaction is promoted at lower temperatures by using an excess of steam and providing a medium- or low-temperature shift catalyst.

In an auto thermal reforming process, 1000 kmol/h of methane at 20 °C is compressed to 10 bar, mixed with 2500 kmol/h of saturated steam, and reacted with pure oxygen to give 98% conversion of the methane.

The resulting products are cooled and passed over a medium-temperature shift catalyst that gives an outlet composition corresponding to equilibrium at 350 °C.

i. How much heat is required to vaporize the steam?

ii. How much oxygen is needed?

iii. What is the temperature at the exit of the auto thermal reforming reactor? iv. What is the final molar flow rate of each component of the synthesis gas?

Reference no: EM131157636

Questions Cloud

How did you evaluate and combine the various pieces of data : Complete your Self-Assessment of the AACN Essentials located in Doc Sharing (Week 1). Note your total score. If you are willing, please share your total score with your classmates. Identify areas where your knowledge is lacking. Keep in mind that ..
What are the advantages to phrs : This can lead to someone shutting off the alarm. Give an example of an ethical or legal issue that may arise if a patient has a poor outcome or sentinel event because an alarm was turned off. What do the data show about the value of alarms in gene..
Sketch a block flow diagram of the process : The product from the trans alkylation reactor is returned to the benzene column. Sketch a block flow diagram of the process.
Demonstrate an understanding of the necessary concepts : Used sufficient and appropriate material from relevant and credible effectively supports the key points demonstrated the ability to critically reflect upon key ideas/issues/findings.
How much heat is required to vaporize the steam : In an auto thermal reforming process, 1000 kmol/h of methane at 20 °C is compressed to 10 bar, mixed with 2500 kmol/h of saturated steam, and reacted with pure oxygen to give 98% conversion of the methane.
How will you get your target population involved : Who is your target population? Where is this intervention taking place? Will it take place one time or multiple times? How will you reach out to your target population?
Brief introduction identifying your topic area : A brief introduction identifying your topic area, a working thesis statement, and a clearly defined statement on the position you are taking in this project
Prepare a project report about the spiritual yoga institute : Prepare a Project report about the spiritual yoga institute. Procedure/Methodology (provides the exact steps taken and methods used for report.
How many cyclones operating in parallel are needed : A fluidized bed is used in the production of aniline by the hydrogenation of nitrobenzene. Single-stage cyclones, followed by candle filters, are used to remove fines from the gases leaving the fluidized bed.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Replace a complete $50,000 loss after 10 years

how much money should be deposited in the fund at the beginning of the program in order to have enough money accumulated to replace a complete $50,000 loss after 10 years?

  Calculate the resistivity using the van der pauw method

Assume that an As i mplant leads to a uniform electron concentration of 1019 cm·3 down to a depth of 0.1 µm and a mobility of 100 cm2 .V1 .s·1 . Determ ine the resistivity and the sheet resisti vity of the implanted layer.

  Calculate the mass of methane

Calculate the mass of methane that must be burned to provide enough heat to convert 363.0 g of water at 43.0°C into steam at 117.0°C. (Assume that the H2O produced in the combustion reaction is steam rather than liquid water.)

  Design a suitable packed column for this duty

The column will operate at 1.1 bar and ambient temperature. If necessary, the aqueous stream may be recirculated to maintain a suitable wetting rate.

  Compute the flux linkage as a function of time

The 50-turn coil in the configuration of Figure P12.1.3 is rotated at a constant speed of 300 r/min. The axis of rotation is perpendicular to a uniform magnetic flux density of 0.1 T. The loop has width w = 10 cm and length l = 1 m

  What is the maximum profit obtainable per pound of chemical

Chemical X costs $0.09 per pound. Chemical Y costs $0.04 per pound. Chemical Z sells for $0.80 per pound. If one-half of the selling price for chemical Z is due to costs other than for raw materials, what is the maximum profit obtainable per pound..

  What is the center temperature

An electric current of 200 A is passed through a stainless steel wire having a radius of 0.001268 m. The length of the wire L is 0.91 m and has a resistance of 0.126 ohms. The outer surface temperature Ts is held at 422.1 K. The average conductivi..

  Determine the motor current and speed

Determine the motor current and speed when the diverter-circuit resistance is made equal to the series-field resistance. Neglect saturation and the voltage drops across the series- field resistance as well as the armature resistance.

  Non-adiabatic operations of flow reactors

Explain Non-adiabatic operations of flow reactors. 15In non-adiabatic operations, heat interchange with the surroundings will beaccounted. The conversion can be defined as the ratio of the net heat still needed after heattransfer to raise the feed..

  Calculate the final temperature of the mixture

Calculate the heat when 100.0 mL of 0.500 M HCl is mixed with 300.0 mL of 0.100 M Ba(OH)2. Assuming that the temperature of both solutions was initially 25.0C and that the final mixture has a mass of 400.0 g and a specific heat capacity of 4.18 J..

  Estimate the power recovered from the preheated gases

If the gases leave the tower at 6 atm, 25 °C, and are expanded to, say, 1.5 atm, calculate the turbine exit gas temperatures without preheat, and if the gases are preheated to 400 °C with the reactor off-gas. Also, estimate the power recovered fro..

  Find the starting current and the starting torque

If a wye-delta starting method is employed, find the starting current and the starting torque.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd