How many helium balloons can be filled in the tank

Assignment Help Civil Engineering
Reference no: EM13312100

a 150 L helium tank contains pure helium at a pressue of 1825 psig. How many 3.5L helium balloons can be filled from the helium in the tank? (Assume an atmospheric pressue (14.7 psia) and a temp of 298K.

Reference no: EM13312100

Questions Cloud

How high will the stream of water rise above the syringe : A syringe is pointed vertically up in the air and a force of 5 lbs is applied to the plunger with a diameter of 0.5 inches. Assuming no losses in the system how high will the stream of water rise above the syringe
What is the drift speed of the conduction electrons : A current of 3.50 A is carried by a copper wire of radius 0.87 mm. what is the drift speed of the conduction electrons
Determine the cycle length and distributuion of green : A simple four-leg intersection needs a 2-phase fixed-time signal. The critical flows in the N-S and E-w directions are 600 and 400 veh/hr, respectively, with a 0.95 peak-hour factor.
Research paper on a topic concerning a current or workplace : Write a research paper on a topic concerning a current or workplace issue or an area covered by the federal or state labour law or the national labour relation board case or issue.
How many helium balloons can be filled in the tank : a 150 L helium tank contains pure helium at a pressue of 1825 psig. How many 3.5L helium balloons can be filled from the helium in the tank? (Assume an atmospheric pressue (14.7 psia) and a temp of 298K.
How far would you have gone if the bike could move : Suppose you are riding a stationary exercise bicycle, and the electronic meter indicates that the wheel is rotating at 9.50 rad/s. how far would you have gone if the bike could move
Determine what is the height of the column of water : If water at 70 degrees C (row=1.94 slugs/ft^3, vapor pressue= 0.363psia) is used in a simple barometer what is the height of the column of water if the atmospheric pressure is 15 psia
Determine the overflow rate and solids loading of clarifier : An activated sludge aeration tank has a width of 14m, a length of 15m and an effective liquid depth of 4.5m. The secondary clarifier has a diameter of 25m. The plant operating parameters are as follows
Stitching together a business with partners : Stitching together a business with partners

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the angle theta for equilibrium from two springs

The 10-lb lamp fixture is suspended from two springs, each having an unstretcfhed length of 4 ft and stiffness of k=5lb/ft. Determine the angle theta for equilibrium.

  Calculate the critical load for strong-axis buckling

we have the I-section made of steel (E = 29,000 ksi) which is to be used as a column, pinned at the top, and fixed at the base. Bracing is to be added in the direction of the weak buckling axis, at an unknown height, H.

  Find tensile stress that will give probability of failure

The median value of the rupture strength was 300 MPa. The ceramic is to be used for components with dimensions l=50mm, b=d=5mm loaded in simple tension along their length. Calculate the tensile stress that will give a probability of failure of the..

  Design a bar screen for a peak average flow

design a bar screen for a peak average flow of 0.46m3/s.you can consider reasonable assumptions.

  Find solubility of substance which dissolve with volume rise

Solubility of a substance which dissolves with an increase in volume and liberation of heat will be favoured by the A. low pressure and high temperature. B. low pressure and low temperature.

  What the meaning of steady state

could you please help me to figure out what the meaning of steady state in the pavement management system preservation and rehabilitation.

  Determine what manometer reading can be expected

Is this flow laminar. What is the viscosity of the oil. For the same flow in the opposite directio, what manometer reading can be expected.

  Determine the velocity and acceleration of block b

Determine the velocity and acceleration of block B and determine the velocity and acceleration of Car A relative to Car B.

  Calculate the cost per kg charged by these two suppliers

Our laboratory plans to use one, 10-liter tank of refrigerant 134a every week. So off you go to check the cost of fill-ups at the two possible suppliers. At Chem Mart, the filled tank is returned to you at 10 bar and 90 C for $10.00.

  Determine the force exerted by the jet on the plate

A jet of water of diameter 75mm moving with a velocity of 25m/s strikes a fixed plates in such a way that the angle between the jet and plate is 60 find the force exerted by the jet on the plate.

  What removal percentage should be expected for particles

A treatment plant has a horizontal flow sedimentation tank with a depth of 4m, width of 6m, length of 36m, and process flow rate of 450m3/h. What removal percentage should be expected for particles that have settling velocities of 1.0 m/h and 2.5 ..

  Describe the measurements that would have to be taken

describe the measurements that would have to be taken and the equations that would have to be used to determine G23, V32, and E2 for a specially orthotropic transversely isotropic material from a single tensile test.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd