How many atoms are found inside a unit cell of simple cubic

Assignment Help Electrical Engineering
Reference no: EM13247002

How many atoms are found inside a unit cell of a simple cubic, body-centered cubic, and faced-centered cubic crystal?
How far apart interms of lattice constant a are nearest neighbor atoms in each case, measured from center to center?

Reference no: EM13247002

Questions Cloud

Which is preferred if the target lifetime of the system : (Probability of negative lifetime is negligible) Lifetime of chip 2 is also a Gaussian RV with mean 22,000 and standard deviation 1000 hours. Which is preferred if the target lifetime of the system is (i) 20,000 hours and (ii) 24,000 hours
Express h in standard form for drawing a bode plot : Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degr..
Calculate ni and the concentration of electrons and holes : An unknown semiconductor has Eg = 1.1 eV and Nc = Nv. It is doped with 10^15 cm^-3 donors where the donor level is 0.2 eV below Ec. Given that Ef is 0.25 eV below Ec, calculate ni and the concentration of electrons and holes in the semiconductor a..
Find atom in unstable state before it spontaneously decays : A sample of radiocactive material undergoes decay such that the number of atoms N(t) remaining in the unstable state at time t is related to the number No at t = 0 by the relation N(t) = No exp(t\tau)
How many atoms are found inside a unit cell of simple cubic : How many atoms are found inside a unit cell of a simple cubic, body-centered cubic, and faced-centered cubic crystal How far apart interms of lattice constant a are nearest neighbor atoms in each case, measured from center to center
What is the standard deviation of the sample mean : What is the probability that the interpupillary distance for a randomly selected male will be between 64 and 67 mm and What is the standard deviation of the sample mean
Write the test bench code to test the design : Write the verilog code for a circuit that counts the number of 1s in a byte. Write the verilog code using a structural approach based on four Half-Adders, two 2-bit adders and one 3-bit adder. Write the test bench code to test the design.
Calculate speed if load torque is reduced to three times : The DC shunt motor is running at full load with a supply voltage of 440 V and a supply current of 70 A. The rotation speed in full load is 1000 rpm, the field resistance is 200 Ohm and the armature resistance is 0.2 Ohm.
Write a matlab function for operation of a half-adder : Write a MATLAB function the performs the operation of a half-adder, call it half_add. The function should have two inputs, a and b, and return two outputs, X and c. Then, write another function, call it full_add, that invokes half_add to perform

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the operation of sequential logic devices

Explain the operation of sequential logic devices and evaluate the output waveform in relation to the clock for QA, QB and QC in the subsequent circuit and show the binary sequence represented by these waveforms

  What is the impedance of the circuit in rectangular form

A series circuit has a 1k(ohm) resistance and a 1k(ohm) inductive reactance. v1= 1 vrms a. what is the impedance of the circuit in rectangular form b. the frequency is given as 1kHz, what is the inductance of the coil L= c.

  How to design a simple unipolar drive circuit

Design a simple unipolar drive circuit such that the electrical time constant is 2 msec at phase turn-on and 1 msec at turnoff. The stepping rate is 300 steps per second. A three-phase variable-reluctance stepper motor has parameters.

  Why latter functions of two variables should be implemented

Implement switching function of 4 variables H(A,B,C,D)= AB'+BC+A'CD using a 4 to 1 Multiplexer and any number of 2 to 1 multiplexer. One can select any 2 variables (for example, AB or CD) as select inputs of one 4 to 1 multiplexer.

  Calculate the equivalent impedance for three parallel loads

Three loads are connected in parallel across a single-phase source voltage of 240 V (RMS). Load 1 absorbs 12 kW and 6.667 kVAR; Load 2 absorbs 4 kVA at 0.96PF leading; Load 3 absorbs 15 kW at unity power factor.

  Determine the discrete implementation peak to peak output

The objective is to design a discrete common-emitter amplifier, the common-emitter amplifier is to have the following specifications: single ended input and output Av approximately 20 in the midband 3-dB bandwidth extending from 10 Hz

  Compute the signal voltage at the detectors output

20 SI fibers, 2 km long each, are spliced together for a 40 km link. Each fiber has a loss rate of 1-dB/km and a numerical aperture of 0.24. Each splice adds 0.5 dB of loss. A laser diode has a threshold current of 10 mA and emits at 3 mW/mA rate.

  What is a relative addressing mode

Discuss different types of addressing modes of HCS12. What is a relative addressing mode What is the difference between a direct and an extended addressing mode Discuss how Registers X and Y are used in index addressing mode.

  Calculate the cycling periods and plot the level vs time

A 10m diameter cylindrical tank is emptied by a constant outflow of 1 m3 /min. A two position controller is used to open and close a fill valve with an open flow of 3 m3 /min. For level control the neutral zone is 1m and the setpoint is 10m.

  Calculate and plot the waveforms for va an ea

The motor driven by a switch-mode dc-dc converter, which has a bus voltage of 200V. The switching frequency fs = 25 kHz. Calculate and plot the waveforms for va(t), ea(t), ia(t), and id(t) under the following conditions

  What is the maximum effective data rate of the link

Consider a satellite communication link with a one way propagation delay of 300ms between the sender and receiver, operating at 10Mbps using packets of length 1500bytes. Length of the ACK packet is also 1500 bytes.

  Compute the number of clock cycles required to execute

1- Describe the function of the program. DO NOT WRITE THE OPERATION OF EACH INSTRUCTION 2- Assuming that the branch instruction is executed (the branch is taken), comput the number of clock cycles required to execute the loop (DECA or BNE AGAIN)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd