Calculate ni and the concentration of electrons and holes

Assignment Help Electrical Engineering
Reference no: EM13247004

An unknown semiconductor has Eg = 1.1 eV and Nc = Nv. It is doped with 10^15 cm^-3 donors where the donor level is 0.2 eV below Ec. Given that Ef is 0.25 eV below Ec, calculate ni and the concentration of electrons and holes in the semiconductor at 300K.

Reference no: EM13247004

Questions Cloud

Determine minimum required bandwidth and baud rate : For a 128-PSK modulator with an input data rate equal to 56 Mbps and a carrier frequency of 100 MHz, determine (a) minimum required bandwidth and (b) baud rate.
Determine the value required for any pre-scaling : A PWM is used in 8-bit mode to produce a signal with a 1 msec period and 60% duty cycle. Determine the value required for any pre-scaling, and the values for the period, and duty cycle registers. The E-clock is 24 MHz.
Which is preferred if the target lifetime of the system : (Probability of negative lifetime is negligible) Lifetime of chip 2 is also a Gaussian RV with mean 22,000 and standard deviation 1000 hours. Which is preferred if the target lifetime of the system is (i) 20,000 hours and (ii) 24,000 hours
Express h in standard form for drawing a bode plot : Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degr..
Calculate ni and the concentration of electrons and holes : An unknown semiconductor has Eg = 1.1 eV and Nc = Nv. It is doped with 10^15 cm^-3 donors where the donor level is 0.2 eV below Ec. Given that Ef is 0.25 eV below Ec, calculate ni and the concentration of electrons and holes in the semiconductor a..
Find atom in unstable state before it spontaneously decays : A sample of radiocactive material undergoes decay such that the number of atoms N(t) remaining in the unstable state at time t is related to the number No at t = 0 by the relation N(t) = No exp(t\tau)
How many atoms are found inside a unit cell of simple cubic : How many atoms are found inside a unit cell of a simple cubic, body-centered cubic, and faced-centered cubic crystal How far apart interms of lattice constant a are nearest neighbor atoms in each case, measured from center to center
What is the standard deviation of the sample mean : What is the probability that the interpupillary distance for a randomly selected male will be between 64 and 67 mm and What is the standard deviation of the sample mean
Write the test bench code to test the design : Write the verilog code for a circuit that counts the number of 1s in a byte. Write the verilog code using a structural approach based on four Half-Adders, two 2-bit adders and one 3-bit adder. Write the test bench code to test the design.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Interface binary i/o devices to the microcontroller

Interface binary Input Output devices to the microcontroller

  Write the analytical expression for the waveforms

What would be the initial value of v c (t) when switch is closed and determine the time constants in both cases (switch is open, switch is closed).

  Which configuration then would have higher input impedance

The input impedance of a JFET used in COMMON SOURCE configuration, is defined by two considerations: The JFET itself has a VERY HIGH INPUT IMPEDANCE, because the input is the GATE to SOURCE junction that is REVERSE biased

  Calculate the electric current moving through

A glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving.

  Laplace transforms enable interpretation and manipulation

Laplace transforms enable interpretation and manipulation of different signals by viewing these signals as either time domain signals/pulse or else frequency domain representations

  Explain operational amplifier - finding the offset voltage

Operational amplifier - Finding the offset voltage, An operational amplifier has a gain of 20. The input voltage is 125mV and the input bias current is zero.

  Design a voltage-divider network to supply the load

The voltage across the load must remain between 4.7 and 5.0 V for all values of load current. Design a voltage-divider network to supply the load. You may assume that resistors of any value desired are available.

  What is its energy after the current drops to zero

1) A 1.5H inductor has a constant current of 2.5A. a) find the energy that it holds b) what is its voltage c) what is its energy after its current drops to zero and stays zero What power is dissipated when a 20 olhm resistor is connected to it

  Consider a communications channel with a passband

Consider a communications channel with a passband of 3 kHz to 27.4 kHz. A modem will be connected to this communications channel and the modem will operate with a signaling rate that is 0.56 the maximum allowable signaling rate for this communicat..

  Determine the image frequency and the local oscillator

1-for an FM reciever tuned to 94.5 MHZ using high side-injection and a first IF of 10.7 MHZ, Determine the image frequency and the local oscillator

  Determine all prime implicants and essential prime implicant

For the equation F(a,b,c,d) = ab'c' + abc'd + abcd + a'bcd + a'bcd', determine all prime implicants and all essential prime implicants: (a) using a K-map, (b) using the tabular method.

  Shielding effectiveness with copper also steel at equality

Shielding Effectiveness with copper and steel at equality, Determine the frequency at which two 1 mm thick shields, one made of copper and the other of steel

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd