Express h in standard form for drawing a bode plot

Assignment Help Electrical Engineering
Reference no: EM13247005

Consider a transfer function (H(s)) that has a double pole at zero, a single pole at negative 1000, a single zero at negative 100 and a gain of 250.
A) Express H(jf) in standard form for drawing a Bode plot.
B) Plot the Bode straight-line approximation for the log-magnitude (LM) response of H(jf) over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper. Label all slopes in dB/oct or dB/dec and all levels in dB.
C) Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degrees.

Reference no: EM13247005

Questions Cloud

Develop prediction interval and confidence interval : Develop prediction interval and confidence interval for y for the value of x you select. Interpret both intervals as they relate to y.
Determine minimum required bandwidth and baud rate : For a 128-PSK modulator with an input data rate equal to 56 Mbps and a carrier frequency of 100 MHz, determine (a) minimum required bandwidth and (b) baud rate.
Determine the value required for any pre-scaling : A PWM is used in 8-bit mode to produce a signal with a 1 msec period and 60% duty cycle. Determine the value required for any pre-scaling, and the values for the period, and duty cycle registers. The E-clock is 24 MHz.
Which is preferred if the target lifetime of the system : (Probability of negative lifetime is negligible) Lifetime of chip 2 is also a Gaussian RV with mean 22,000 and standard deviation 1000 hours. Which is preferred if the target lifetime of the system is (i) 20,000 hours and (ii) 24,000 hours
Express h in standard form for drawing a bode plot : Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degr..
Calculate ni and the concentration of electrons and holes : An unknown semiconductor has Eg = 1.1 eV and Nc = Nv. It is doped with 10^15 cm^-3 donors where the donor level is 0.2 eV below Ec. Given that Ef is 0.25 eV below Ec, calculate ni and the concentration of electrons and holes in the semiconductor a..
Find atom in unstable state before it spontaneously decays : A sample of radiocactive material undergoes decay such that the number of atoms N(t) remaining in the unstable state at time t is related to the number No at t = 0 by the relation N(t) = No exp(t\tau)
How many atoms are found inside a unit cell of simple cubic : How many atoms are found inside a unit cell of a simple cubic, body-centered cubic, and faced-centered cubic crystal How far apart interms of lattice constant a are nearest neighbor atoms in each case, measured from center to center
What is the standard deviation of the sample mean : What is the probability that the interpupillary distance for a randomly selected male will be between 64 and 67 mm and What is the standard deviation of the sample mean

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the sensitivity of junction depth to changes

how to determine the sensitivity of junction depth to changes in furnace temperature by calculating (dxj/xj)/(dT/T) for a drive diffusion.

  Calculate the annual saving in electrical usage in us

induction cooking based on power electronic is estimated to be 80 percent efficient compared to 55 percent for conventional electric cooking . if an average home consumes 2 kw-hrs daily using conventional electric cooking.

  Find speed of an electron beam coming from an electron gun

The axis of the cylinder is along the z axis, and the electrons are moving with a velocity vector v in the positive z direction. The velocity of the electrons is 0.1c where c is the speed of light (2.99792458 ´ 108 [m/s]). The magnitude of the cur..

  What is the signal-to-noise ratio of the spread signal

Suppose that a voice signal normally occupies 30 kHz of bandwidth and has a signal-to-noise ratio of 20 dB. Spread-spectrum techniques are used to increase its bandwidth to 2 MHz. (a) What is the signal-to-noise ratio of the spread signal

  Find the output voltage

A temperature sensor has a static transfer function of 0.15 mV/C° and a time constant of 3.3 s. If a step change of 22° to 50° C is applied at t=0, find the output voltage at 0.5 s from t=0s to t=10s

  How many grams of carbon were present in the original sample

(b) If the molecular weight of bombykol is 238.4 amu, what is the molecular formula (c) If 5.698 g of bombykol is burned in excess oxygen to form 16.83 g of CO2 and 6.452 g of H2O, how many grams of carbon were present in the original sample

  How to create a circuit to connect the two video sources

A video system can accept video from one of two video sources, but can only display one source at a given time. Each source outputs a stream of digitized video on its own 8-bit output. A switch with a single bit output chooses

  Find correlation coefficient between input x and output y

The output of a communication channel is Y = X + N where X and N are independent, zero mean, random variables. X represents signal and N is noise. (a) Find the correlation coefficient between the input X and the output Y.

  Define the angle of departure is defined

The angle of departure is defined as 180 degrees plus the phase angle of GH computed at the complex pole, but ignoring the contribution of that particular pole.

  How to keep the voltage variation below 5v peak-to-peak

The output capacitor in a certain resonant converter sees the net current equal to 40cos(50,000 pi t) A. What value of capacitance will be needed to keep the voltage variation below 5V peak-to-peak

  Find the total resistance and the current

constructed using standard value resistors a. Without making a single calculation, which resistive element will have the most voltage across it Which will have the least b. Which resistor will have the most impact on the total resistance.

  How to control shopping center parking lot lighting system

A control system is needed to control a small shopping center parking lot lighting system and the exterior lighting for the building. The design specifications require that the parking lot lighting and the exterior lighting turn on at dusk automat..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd