How long in hours will it take to reduce the concentration

Assignment Help Civil Engineering
Reference no: EM13314204

One way to treat amd is to treat the metals in a holding pond. The first order rate constant is 10/day. The concentration in the water must be below 5 ppm. How long in hours will it take to reduce the concentration from 250 ppm to 5 ppm? Assume no flow in or out

Reference no: EM13314204

Questions Cloud

What is the total charge on the interior : A charge +7.4 %u03BCC is placed at the center of the hollow spherical conductor with the inner radius 3.2 cm, What is the total charge on the interior
Find the angular acceleration of the merry-go-round : A merry-go-round starts from rest and accelerates uniformly over 11.0 s to a final angular velocity of 7.50 rev/min, Find the angular acceleration of the merry-go-round
Determine the present worth for physical asset investment : Inital Cost=$40,000, Estimated Salvage Value (@ year 5)=18,000, Actual Salvage Value (@ yr.5)=20,000, Depreciation: Straight-Line (No half -year convention), Life=5yrs, Annual Benefit=10,000, and tax rate=34%.
Is it important to include a policy that outlines the origin : Why is it important to include a policy that outlines the origin and scope of purchasing authority? What might happen if such a policy did not exist?
How long in hours will it take to reduce the concentration : One way to treat amd is to treat the metals in a holding pond. The first order rate constant is 10/day. The concentration in the water must be below 5 ppm. How long in hours will it take to reduce the concentration from 250 ppm to 5 ppm
What is the drivers average velocity : A driver travels 10 km east, 20 km north and 50 km in a direction 30 degrees south of west. What is the drivers average velocity if the trip takes 90 minutes
At what distance will the concentration of metals be 5 ppm : Assume the stream is 3ft wide and 1ft deep (assume a rectangular cross section. If the flow throught the stream is 1000 gallons/day and the concentration at the beginning of the stream is 250 ppm
Compute the speed of the skater : A 75kg skater starts his skate at 4m above ground, the horizontal distance to the bottom of the track is 6m. Calculate the speed of the skater at the bottom of the track
Explain why custom officers,exporters,importers,carriers : Explain why custom officers,exporters,importers,carriers and shippers must have some knowledge or training on dangerous goods?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Should the soil be compacted at the dry of optimum or at wet

A soil is to be compacted on a site and it is expected that the soil contains a high percentage of montmorillonite. Briefly explain the working principles of two tests that can be carried out to ascertain the presence of montmorillonite in the soil.

  Give beam deflection solution

Beam Deflection Solution, Derive an expression for the deflection due to shear for a cantilever beam of constant rectangular cross section, under action of a point load, P at free end.

  Design rectangular sections for beams-loads and values given

fy=50000psi, f'c=3000 span of l=28 ft, dead load not including beam weight = 3 k/ft, live load=3 k/ft, p*=0.5pb, concrete weights=150 lb/ft cubed, use h=d+2.5 inch, assume beam weight =10kN/m and phi=0.90

  How to identify the sources of information presented at work

The knowledge of the geological and geotechnical characteristics of the subsoil is a basic step, fundamental to the development of any type of research, evaluation, study or project in the areas of Civil and Environmental Engineering.

  Determine what is runoff coefficient in a basin located

What is the runoff coefficient in a basin located near the middle of the climatic spectrum, with annual precipitation P = 32 in, ecosystem evapotranspiration ET = 22 in, and baseflow U = 3 in

  Design the pipe to flow capacity and use a mannings n

Determine the diameter (in inches) and velocity (feet per second) of a concrete storm pipe required to carry a peak flowrate of 20 cfs at a slope of 1.0% Design the pipe to flow at 75% capacity and use a Mannings n of 0.013.

  Elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

  Determine the coefficient of friction

a mass of 2kilogram is projected with a speed of 3m/s.if a plane inclined 20 degrees with the horizontal.after travelling travelling 0.8meters, the mass comes to rest. determine the coefficient of friction and also the speed as the black returns t..

  Find how much would the pressure in the tank increase

A rigid tank contains 5kg of water at 20 degrees Celsius. A gage on the tank reads 200kPa. Determine a) the volume of the tank, b) How much would the pressure in the tank increase if the temperature were increased to 50 degrees Celsius.

  What is significant difference between free jets and flows

What is the most significant difference between "free" jets and flows in confined structures (nozzles, pipes, etc.) in terms of formulation of force terms ÓF(i.e. left hand side) of the momentum equation

  Calculate the degree of saturation and dry density

Soil has been compacted in an earth dam to a bulk density of 2.2 Mg/m3 and a water content of 9.5%. The value of Gs is 2.6. Would it be possible to compact the above soil at a water content of 13.5% to a dry density of 2.00 Mg/m3

  Find the final temperature and the amount of work

Air can be assumed as a di-atomic ideal gas. Find the final temperature and the amount of work ( in kW) required for air compression at a rate of 100 mol/s , from an initial condition of 1 bar an 25 C to 10 bar; for the following ways.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd