Give the phase and the missing property of

Assignment Help Civil Engineering
Reference no: EM13529940

1.Give the phase for the followingstates.

a) CO2 T=267celcius P=0.5

b) Air T=20 celciusP=200kPa

c) NH3 T=170celcius P=600kPa

Label them onto P-v and T-sdiagrams.

2.Give the phase and the missing property of P, T, v and x. Put the values in a table withcolumns P, T, v, and x.

   a) R-134a T=-20 celcius, P=150 kPa

   b) R-134a P=300 kPa, v=0.072 m3/kg

   c)CH4 T=155 K, v=0.04 m3/kg

   d) CH4 T=350 K, v=0.25 m3/kg

Reference no: EM13529940

Questions Cloud

An unknown immiscible liquid seeps into the bottom of an : An unknown immiscible liquid seeps into the bottom of an openoil tank. Some measurements indicate that the depth of theunkown liquid is 1.5m and the depth of the oil ( specific weight =8.5
Find the magnitude of the hanging blocks acceleration : Two blocks are connected by a string. The smooth inclined surface makes an angle of 35 degree with the horizontal, Find the magnitude of the hanging block''s acceleration
Determine the anualvolume of solid waste produced by : The Bailey stone work employs six people. assuming that thedensity of uncompacted waste is 480 kg/m^3 determine the anualvolume of solid waste produced by the stone works assuminga wastegeneration rate of 1kg/cap *d
Obtain the potential difference between the two points : A uniformly charged infinite sheet with a surface charge density +? lies flat in the x-y plane. What is the potential difference DV between the two points
Give the phase and the missing property of : Give the phase and the missing property of P, T, v and x. Put the values in a table withcolumns P, T, v, and x.
What is the maximum amount of soluble : If the solubility product of magnesium hydroxide is 11.25 answerthe following question. If water at 25-degree C is bufferedsuch that the pH remains fixed at 7, what is the maximum amount ofsoluble Mg2+, in grams, in 1L of water?
How fast are is he going at the bottom : The skier starts at a snow covered slope which is inclined 20 degrees above the horizontal. The skier has a mass of 100kg. How fast are is he going at the bottom
Explain why the two graphs would be the same or different : Suppose a cart was given a push down a ramp, starting at the end close to the motion detector, Describe what the acceleration vs. time graph will look like for this case, Explain why the two graphs would be the same or different
What is the mass of the object : The electric field between the plates of a parallel-plate capacitor is horizontal, uniform and has a magnitude E. What is the mass of the object

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the volume of fill that will be produced and express

The average unit weight of this soil is 118 lb/ft^3, and the average moisture content is 9.6%. It also has a maximum dry unit weight of 122 lb/ft^3 and an optimum moisture content of 11.1%

  Draw the event tree and for the initiating event

An intelligence data bank center requires power 24 hours a day, 7days a week. If the main power grid fails, a backup power supply isinitiated.

  Determine final height of the fill after compaction

A 2 m high sandy fill material was placed loosely at a relative density of 47%. Laboratory studies indicated tht the maximum and minimum void ratios of the fill material are 0.92 and 0.53, respectively.

  You have been hired to design a horizontal curve

You have been hired to design a horizontalcurve with a 40 degree central angle ( delta= 40) for a two-laneroad with 10 ft lanes. If the design speed is 70 mph, emax=6%

  Find what is the minimum radius of curvature for a curve

The coefficient of friction between a car's tires and the road is such that the car can generate a maximum deceleration of 1.1g without experiencing slip.

  Determine the temperature of propane in the tank drops

determine the temperature of propane when the pressure in the tank drops to 1 atm. Also determine the total amount of heat transfer from the environment to the tank to vaporize the entire propane in the tank.

  What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

  Calculate the degree of saturation and dry density

Soil has been compacted in an earth dam to a bulk density of 2.2 Mg/m3 and a water content of 9.5%. The value of Gs is 2.6. Would it be possible to compact the above soil at a water content of 13.5% to a dry density of 2.00 Mg/m3

  Determine the normal stresses induced in portions ab and bc

A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E=29x10^6 psi, α=6.5x10^-6) and portion BC is made of aluminum (E=6.5x10^-6 psi, α=13.3x10^-6).

  What reading of the compass should be used to retrace line

IT IS DESIRED TO RETRACE THE LINE WITH A COMPASS TODAY, WHEN THE DECLINATION IS 5 35'E. WHAT READING OF THE COMPASS SHOULD BE USED TO RETRACE THE LINE

  Determine distance the officer traveled before overtaking

The officer believes the driver is intoxicated and begins accelerating uniformly to 50 mi/h in 8 seconds and maintains a constant velocity of 60 mi/hr, overtakes the motorist 42 seconds after he passed the officer.

  Calculate the maximum deflection of the beam

A 30" beam with a cross section of 1" wide and 2" tall is supported by a pin at point A on its left end, and a roller at point B on its right end. A 300 lb force is exerted 10" to the right of A (20" left from B)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd