Find the rate of change in volume

Assignment Help Civil Engineering
Reference no: EM13207704

A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.

Reference no: EM13207704

Questions Cloud

Determine the net rate of flow of linear momentum : Determine the net rate of flow of linear momentum through the control surface.
What is the corrected measurement : A measurement was recorded as 171.278 m with a 30-m tape that was only 29.996 m under standard conditions. What is the corrected measurement?
What fraction of the herbicide is adsorbed : The herbicide 2,4,D, is applied to a golf course at a rate of 1.2 kg/ha. The organic matter content of the soil is 1%, bulk density is 1.3 g/cm3, and water content is 0.3.
Compute the specific rotation of the compound : An aqueous solution containing 9.47 g of an optically pure compound was diluted to 200.0 mL with water and placed in a polarimeter tube 20.0 cm long.
Find the rate of change in volume : A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.
Which of the two people is less likely to take on risk : A driver faces a 5% probability that his car will be in an accident and will be worth nothing. Consider three drivers with cars that have value $30,000. Abdulla's utility function over the value of his car W is u(W) = ln(1 + W).
Calculate the hydraulic conductivity of this clay : A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm. Calculate the hydraulic conductivity of this clay.
How much caco3 is produced per hour : A slurry containing 20 percent by weight of limestone (CaCO3) is processes to separate pure dry limestone from water. If feed rate is 2000kg/h, how much CaCO3 is produced per hour?
Soil erosion caused by plowing a steep hillside : Which of the following mechanisms of environmental change is exemplified by soil erosion caused by plowing a steep hillside?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Allowable shearing stress

The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. Knowing that the torque of magnitude T=10 kip * in. is applied at A, determine the required diameter of a) rod AB, b) rod BC.

  Define the front of our library has six double doors

the front of our library has six double doors and the doors rotate open in the middle making less clerance room how can i get started

  Calculating the principle of shoring system

How to calculate the principle of shoring system in formwork analysis when the secondly floor upper has been poured?

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  Elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

  Define introduction to management science

Introduction to management science, The Dynaco Manufacturing Company produces a particular product in an assembly line operation. One of the machines on the line is a drill press that has a single assembly line feeding into it.

  Determine the compression of each spring

The 75 lb block is released from rest 5 ft above the plate. Determine the compression of each spring when the block momentarily comes to rest after striking the plate.

  Problem of coefficient of static friction

The machine part ABC is supported by a frictionless hinge at B and a wedge at C. Knowing that the coefficient of static friction is 0.20 at both surfaces of the wedge, determine:

  Related geotechnical engineering

This material is related Geotechnical Engineering, please only answer if you are certain and sure of your answer. An undisturbed soil sample has a dry unit weight of 112 pcf with a specific gravity of solids equals to 2.68.

  Compute the maximum acceptable service load

Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.

  Engineering ethics and ethical issue

what is the engineering ethics course where to write about any engineering ethical case and discuss the ethical issue?

  Superelevation rate for a roadway

What superelevation rate would you recommend for a roadway with a design speed of 100 km/hr and a radius of curvature of 500 m? Assume f = 0.11.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd